Question about Chrysler Town and Country

Open Question

Where is the heater hose assembly located on 2008 chrysler town and country

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

  • 49 Answers

SOURCE: error codes 442 and 456 on 2003 Chrysler Town and Country

Could be the gas cap.  Do you fill the tank with the engine running?
Otherwise, check the hoses near the Evap canister.  I have 2003 T&C and had the small leak and large leak codes.  I looked at the evap cansiter and the hose coming from the fuel tank vapor line had a huge crack in it, to the point it had fallen off the evap caniser.  I trimmed the end of the hose and reconnected and voila, no codes.
The evap canister is on the driver's side of the van, underneath, slightly behind the drivers seat.
BTW, to clear the codes without an OBDII reader, remove the negative cable for 5-10 minutes (15 to be safe).  The computer resets and clears the codes, except for one that it sets saying loss of power to the memory.

Posted on Jan 24, 2009

emissionwiz
  • 75807 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

hunterd777
  • 14 Answers

SOURCE: Early wear on front brakes /rotors for 2008 Town and Country

I work for a brake repair shop and trust me you are not alone.Enterprise and alot of other people bought the same van and had the same trouble.I hate to say but it doesnt stop there.About every 14 to 15 thousand miles you have to replace the front pads.As of now they dont have an upgrade,for instance ceramic pads, but I am sure they will very soon

Posted on May 01, 2009

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Picture of heater hose connections 3.8 chrysler town and country?


Not here

We are at home & use the site like you do

Google --try that or You Tube Video

Jul 17, 2014 | 2008 Chrysler Town & Country

1 Answer

I have a coolant leak in a 96 town and country


TRACE LOCATION AND FIX, HOSE OR CLAMP OR RADIATOR OR HEATER CORE IN DASH . IT IS A SMALL CLOSED SYSTEM UNDER PRESSURE

Nov 03, 2013 | 1996 Chrysler Town & Country

1 Answer

Fuel filter on a 1999 chrysler town and country


I belive the filter is in the fuel tank, its an integeral part of the pump/pickup assembly

Aug 08, 2012 | 1999 Chrysler Town & Country

1 Answer

96 CHRYSLER TOWN AND COUNTRY THE PASSENGER SIDE FLOOR IS SOAKING WET THE HEATER CORE IS ON DRIVER SIDE WHAT COULD BE LEAKING


heater core is actually centered behind controls- plumbing connections are on passenger side-look in engine compartment for leak first- loose clamp or split hose- then go to core- can try BAR's Leak first if not a hose problem

May 18, 2011 | 1996 Chrysler Town & Country

1 Answer

My 2001 Chrysler Town & Country recently loss it's heater ability. When engine is warm, it barelys puts on at the highest setting. I changed thermo stat which did look worned but no help yet. I can't...


Since your blower is working and it is a heat issue,thats where we'll start,First thing is have you checked the coolant level in the radiator when engine is cold,make sure it is filled to top,next verify you have coolant in reserve ,Start your van and get it up to normal operation temperature,If your heat gauge on the dash works correctly it should be 190 degrees,Now lift the hood and locate the two heater hoses going into the heater assembly at the fire wall,Both hoses should be hot to hold on to,if both are hot and no heat inside your problem will be the blend air door in heater assembly.
if neither hose is that hot you need to replace the thermostat in the engine to get it up to 195 degrees.
if one hose is hot and one is luke warm then the heater core is blocked and to blame. hope this helps you

Dec 31, 2009 | 2001 Chrysler Town & Country

1 Answer

Where is the block heater cord on a 2008 Chrysler Town & Country Limited?


it should be in front near the grill, was there a block heater installed on this van? if you look at the engine were the freeze plugs go ,if a heater was installed you should see the element in one of the freeze plug holes instead of a freeze plug, if there is one then follow the cord, hope this is helpful, good luck.

Dec 12, 2009 | 2008 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...