Question about Cars & Trucks

1 Answer

90 ford bronco lost 3rd gear - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 460 Answers

There's only two real solutions here. One is replacing the control module in transmission inside of pan bolted to valve body. Pretty straight forward and easy to replace once trans pan is off and filter removed. Second is the trans mission needs to be rebuilt. If the gear 3 is gone the expect trans rebuild

Posted on Jan 23, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

  • 27 Answers

SOURCE: 90 ford bronco is cold blooded

There is a sensor on the manifold called the ACT, air charge temp. if it is malfunctioning it can cause this behavor. Run codes and see what it shows. if you dont want to by a scanner you can find full instructions on how to pull codes manually at fordfuelinjection.com

Posted on Aug 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Ford Bronco II manual transmission extremely hard to shift will not go into reverse


90 Ford Bronco II: You have to put it in whichever gear you want it in before you start it or it wont shift at all. Then once you are going its extremely hard to shift into the other gears. Reverse is the only gear that sounds like its grinding.

Aug 16, 2013 | 1990 Ford Bronco II

1 Answer

1988 Ford Bronco II shifts into 1st and 3rd gear hard and some times pops out of gear.


Sounds like the first and third gear synchronizer is worn out.
You might want to talk to a transmission shop to confirm.

Feb 28, 2013 | 1988 Ford Bronco II

1 Answer

My AT will shift into 3rd, but I have no power, it never makes it into OD. 1st, 2nd and reverse are OK. thanks rob


This could be a problem with the solenoid. It is like a motor that is associated with the change of gears. It could also be the the valve for the 3rd gear. No or minimum oil pressure is supplied to the system. It may also be the torque converter. First step is to ensure that you have good oil in your transmission. Inspect if it needs replacing together with the filter.

Apr 13, 2011 | 1988 Ford Bronco

1 Answer

1994 ford bronco rear window wont go up or down


IF YOU CAN HEAR THE WINDOW MOTOR CLICKING WHEN YOU TRY TO CLOSE IT, IT'S PROBABLY THE PLASTIC GEARS (COMMON PROBLEM) I PICKED ONE UP FOR $25. IF THERE OS NO NOISE WHEN YOU HIT THE SWITCH IT IS EITHER A SHORT OR THE MOTOR ITSELF $90. IT'S THE SAME MOTOR AS YOU FRONT DOOR WINDOWS.

Sep 08, 2010 | 1994 Ford Bronco

1 Answer

What years will 1990 bronco 11 engine and driveline work ?


85-91 bronco II or ranger 2.9 cid
front drive shaft 85-90
rear drive shaft 89-90

Mar 29, 2010 | 1990 Ford Bronco II

1 Answer

I have an 86 ford bronco II. Ive been driving around with the tranny not going into 4th gear. Today I was driving and the tranny started to completely slip into 3rd gear, almost like going into neutral....


I would have to say no,there is nothing else you can do now. Does the fluid smell burned? Is it discoloured? If it is ok now after the top up and additive ,consider your self lucky.

Sep 30, 2009 | 1986 Ford Bronco II

1 Answer

1988 bronco automatic transmission


3rd and 4th gear clutches are the same. The overdrive section is worn out thus resulting to this problem. have the transmission repaired with a new overdrive section.

Mar 05, 2009 | 1988 Ford Bronco

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

1 Answer

1988 Bronco II transmission pop out of 1st gear


there are dent and brass balls that are in your transmission and are used to hold the shifter into each gear when it starts poping out of that means that those dents and brass balls are worn down and i would suggest getting the transmission rebuilt.

Dec 16, 2008 | 1988 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...