Question about Cars & Trucks

Open Question

Megane front fog lights stopped working

Power going 2 foglights. bulbs working. fuses dont know how 2 check them

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Headlights and foglights dont work.Checked fuses and replaced

I had the same problem. The solution to this is something called the turn signal/highbeam switch, located in your steering column. This switch has an actuator of some sort that goes bad after a while. It doesn't allow the actuator to turn back into regular headlight mode, instead disabling it. I went to my local junkyard and replaced it. Everything works now. Here is a link to anyone looking to solve their problem - http://www.am-autoparts.com/AM/Switches-and-Levers/Dodge/Intrepid/-/AM-38623751/

Posted on Dec 27, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: Need fuse schematic

if the fuse was blown the stop lights on both sides would be inop, also if the stop light circuit were dead u would be unable to get the trans out of park, use a 12 volt test light and test the brake light switch at the top of the brake pedal, u can buy a test light from Autozone, kragen and others for about $5 US. If the system has power cjheck the bulb socket it may be defective, use the 12 volt test light while someone pushes the brake pedal. let me know what u find and i will give u further assistance as ness.

Posted on Jan 13, 2009

  • 28 Answers

SOURCE: 98 Jeep Cherokee Fog lights

It's definitely the switch...I bought two of 'em so far...known bug. I don't use the fog lights as much anymore , but the "Airtex" oem equivalent switch from Rockauto seems to be holding up well. If you dissamble your broke switch you'll probably see evidence that it is beginning to melt and theres alot, maybe too much, grease, which may or may not have been the cause of the bad, heating contacts inside switch.
If I remember right, even though the foglights have a relay there is still full amperage going through the switch or something....don't qoute me on that last statement.

Posted on Feb 14, 2009

  • 1 Answer

SOURCE: FRONT FOG LIGHTS

I understand that you remove the wheel and the wheelarch liner and reach it from the rear.
Paul

Posted on Mar 13, 2009

  • 9 Answers

SOURCE: fog light bulbs

You need to remove the plastic under the car, it should either be bolted or screwed in. Pull this down and you should have access to the bulb, a rubber cover and a clip holds the bulb in. No need to remove the entire housing.

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Dodge Avenger R/T fog lights not working


Check the light bulbs themselves. If those are still good, (don't touch the glass on the bulb), then check all your fuses. Chances are, the foglight fuse is linked in with something else.

Jan 15, 2014 | Dodge Avenger Cars & Trucks

1 Answer

Renault scenic front foglight bulb


I found the easiest way to change the fog light bulb is to take bumper off, takes 5 mins, 5/6 screws/clips across the top were the bonnet meets the bumper and a few clips on wheel arches then pull off and 2 spot lights very easy to Accra.

Mar 31, 2012 | 2003 Renault Renault Scenic 1.6

1 Answer

One fog light in 3003 vw golf not working - repalaced bulb, there does not seem to be a particular fuse on the fuse diagram?


depending on country,most golf DO NOT have 2 rear foglights,this is not to confuse the driver behind thinking they are your brake lights,the one that works is fitted/wired to the offside.it still has a bulb holder though........the fronts have a fuse for both(when fitted)

Feb 25, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Verona 2005 fog lights won't work. Fuses are ok, lightbulbs are ok. Fog light switch lites.


Remove the entire foglight assembly check for a loose wire inside the assembly. I had the same problem on mine but it only affected one of the foglights. Also check with a test light at the connector where it connects into the foglight assembly. Also make sure foglight bulbs are properlly tighted.

Dec 08, 2009 | 2005 Suzuki Verona EX

1 Answer

Fog lights do not work on a 1999 9-3 SAAB. no blown fuses and not power at fog light connector, looking for a schematic.


I had same problem in my 1995 saab900,
the fog light contains a bulb and two cables (ground and hot).
the ground cable connects to the bulb base by a connector, this connector collects salt because of the high current and humidity I guess, which made inconductive.
Just cutting the connector and solder the cable directly to the bulb base solved the problem.

the schema is like that:
1- foglight switch give low current to a relay under the hood.
in the same time the switch will get current from the normal ligth so it wont work untill you put the lights on.
2- the current goes from to the relay makes the relay connects the fuse current (from battery via fuse) to the ligts directly.
so the connection is straight forward.

the components involved are:
1- fog light switch.
2- fuse inside the car on the left side of the stearing wheel.
3- fuse under the hood to the top right side of the engine if you look at it from the car front.
4- in the same fuse box under the hood there is a samll relay.
5- cables takes the current from the relay to the foglights.
6- the fog lights have a connection at the back, and connection inside.

make sure you measure each points with a multimeter and in doubt make temporary cables like ground directly to the battery to make sure you don't miss anything.
good luck and email me if you still have problem
ausrasul@gmail.com

Nov 08, 2009 | 1999 Saab 9-5

1 Answer

2002 volvo s60


Log on to www.autozone.com. You sign up for a free online account and add your vehicles to your virtual garage. When you add a car, they give you access to free manuals online that have diagrams and how-to information, among which are electrical system schematics and diagrams.

i hope this helps you a little,
matt

Sep 21, 2009 | 2002 Volvo S60

1 Answer

1999 grand am. low beams dont work. i checked all fuses and relays. ideas????


Lets start by checking the fog lamps. Turn the headlights on, switch to low beam, turn on the fog lights and see if they come on. If the foglights don't work, then you don't have voltage on the low beam circuit to the BCM. If you do have foglights, then the low beam circuit is providing voltage to the BCM.
By determining if the foglights work or don't work we will be able tell what side of the circuit we need to work on.
Let me know.
Regards,

Sep 05, 2009 | Pontiac Grand Am Cars & Trucks

2 Answers

Foglights not working


Junction box under the hood, left fender.

Apr 05, 2009 | 2001 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...