Question about 2000 Chrysler Town & Country

1 Answer

Power locks and seat ajustment switches stopped working

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

Sounds like a bad body control module

Posted on Jan 03, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

92 buick power locks stopped working

On my F250 when the windows went out I had to replace the drivers side switch to get both working again. I am putting my money on the switch is bad. Some of these control panels are all wired together in one so it would make sense that your seats went out as well if all controls are on the arm rest. This on the up side is not a difficult or that expensive to fix on your own.

Aug 31, 2012 | 1992 Buick LeSabre

2 Answers

Passenger power seat on my 2002 CLK will move forward only and not backwards, how do I get it to work ?

Wiggle the switch that controls the problem movement, if the seats moves or jitters a little the switch is defective and will solve the problem. If nothing happens when you do this simple test then go under the seat and probe the large wiring connector the power seat transmission, when you move the switch to rear seat travel position and see if any of the wires light up, if it does show voltage when the switch is toggled then the seat transmission may be at fault. I think you have a switch problem based on my expereinces but do the testing because the part is not cheap.

Jul 17, 2012 | 2000 Mercedes-Benz CLK

1 Answer

Power window buttons only work from driver's seat.

Nope its most likely the switch has gone bad...thats very common on those cars

Btw, I’m available to help over the phone in case u need at

Aug 27, 2009 | 1997 Ford Taurus

1 Answer

How to remove the passenger seat controls, seat will not return to upright position.

Try Electrical contact cleaner ( I get mine at Radio Shack) on the switch sometime they get dirty and stop working. Its the first thing I try it works on power switches windows, seats locks ect.

Aug 12, 2009 | 1999 Jaguar XK8

1 Answer

1993 Ford F150 4X4 Power door locks, power window on passenger side and lumbar control on seats stopped working


Aug 11, 2009 | Ford F-150 Cars & Trucks

1 Answer

1998 E230. power seats,central locking,power windows, turn signals, wipers, power mirrors all stopped working

hello,check your fuse number 4 ,15 for signal light ,check also the rear fuse box for power window,central lock,power seat ,located at rear seat in front of battery,ty

May 01, 2009 | 1999 Mercedes-Benz E-Class

1 Answer

1991 range rover passenger seat doesn't move

You could try swapping out the seat switch from the other side if you are just trying to move the **** portion forward or backward. What usually goes wrong is the seat switch gets corroded and needs to be disassembled and rebuilt. The opposite seat switch will no fit the other side and mount but you can finesse it around to a position where you can make connectioin.

To remove seat switches - Use a small screw driver to carefully pry up the button control knobs (**** and back knobs) on top of the switch housing. Next, remove the cover plate and there you will have 2 screws exposed to remove the switch.


Mar 22, 2009 | 1990 Land Rover Range Rover

1 Answer

My alarm keeps going off on my audi a3 1.9tdi 55 plate, it doesnt sound like the normal alarms which come off the horn its more high pitched,i have tryed double locking the car but its still goes off when...

you need to get it code read,there you can see the last four alarm source and take it from the code,my guess will be interior monitoring,i think you have a switch on the drivers door pillar behind the seat belt,press it when you get out to see if it stops the alarm going off...the tone can be ajusted with vcds software

Feb 18, 2009 | 2007 Audi A3

2 Answers

Power seat and Alarm System

Hold the LOCK and UNLOCK buttons together on your remote. That switches the alarm from SILENT to NOISE mode and wiseversa.

Oct 13, 2008 | 2002 Nissan Pathfinder

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides