Question about Cars & Trucks

1 Answer

Chrysler LHS 1997 turns over but will not start. Already replaced crank sensor twice, and coil pack. Recently had water pump replaced an heads resurfaced. Relay seems fine. It will start an run just

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

Is there spark at the coil? if you sparter fluid will it start

Posted on Jan 03, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: 1997 GMC Yukon won't start.

WHEN YOU REPLACED THE FP DID YOU OR THE DEALIERSHIP REPLACE THE FUEL FILTER MAYBE YOUR PROBLEM ....

Posted on Dec 09, 2009

Testimonial: "They did replace the filter but thank you very much for the tip."

nvannoy
  • 234 Answers

SOURCE: 1995 CRYSLER LHS,WONT START AT ALL,TRIED CHANGING

If it is cranking with out turning over I would check the fuel pump and ignition relay, crank and cam sensors.
Basically you need to figure out if you have a spark issue or a fuel issue. (as long as you didn't have a serious overheating problem). One way to help you figure this out is by spraying in some starting fluid while cranking the engine. If it starts you have a fuel problem, if nothing then you have a spark problem (assuming you didn't blow the head gasket from overheating and was running normally before this happened).
Based on what you've already done here are my recommendations:
No spark: check ignition relay
No fuel: check fuel pump relay (aka shutoff relay, aka fuel pump shutoff relay), crank and cam position sensors, fuel filter.
There is also one other possibility, that the timing belt snapped. You would need to remove the timing cover to check this.

Posted on Feb 05, 2010

  • 381 Answers

SOURCE: 1997 chrysler lhs turns over but no spark.

Try the crank sensor this is the sensor most likely to cause this not the cam sensor. To get to the crank sensor you will have to jack up the passager side of the car and the sensor is located on the transmission bell housing about 3/4 of the way up on the trans were it connects to the engine.(all on the passager side of the trans) It has a 3 wire plug and one 10mm bolt that holds it in. Hope this helps

Posted on Mar 29, 2010

  • 381 Answers

SOURCE: i have 97 chrysler lhs 3.5l that just died on me

I would check the timing belt probably broke. Best way pull the cam sensor out take a flashlight shine it down in the hole and have someone turn it over. u should see it turning if you don't the timing belt is broke. good luck

Posted on Mar 29, 2010

  • 973 Answers

SOURCE: my 2002 dodge grand caravan 3.8 l keeps

You could have a clogged Catalytic Converter which would cause the backfiring and non -starting issue.

Posted on Jun 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 97 lhs that wont start we have replaced


a double post? see my long answer, on 1st post.

Oct 02, 2013 | 1997 Chrysler LHS

1 Answer

Why wont my 1995 chrysler lhs coil pack get a spark?


Its probably a bad crank position sensor or cam angle sensor.

Less likely, it could be a broken timing belt, bad ASD relay, or bad ECU(PCM).

Jan 21, 2011 | 1995 Chrysler LHS

1 Answer

1997 chrysler lhs turns over but no spark. already changed Cam pos. Sensor and Coil block


Try the crank sensor this is the sensor most likely to cause this not the cam sensor. To get to the crank sensor you will have to jack up the passager side of the car and the sensor is located on the transmission bell housing about 3/4 of the way up on the trans were it connects to the engine.(all on the passager side of the trans) It has a 3 wire plug and one 10mm bolt that holds it in. Hope this helps

Mar 06, 2010 | 1996 Chrysler Concorde

1 Answer

1995 CRYSLER LHS,WONT START AT ALL,TRIED CHANGING SENSORS,FEUL PUMP,COIL PACKS AND COMPUTER BOXES,JUST WONT START?ANY IDEA?


If it is cranking with out turning over I would check the fuel pump and ignition relay, crank and cam sensors.
Basically you need to figure out if you have a spark issue or a fuel issue. (as long as you didn't have a serious overheating problem). One way to help you figure this out is by spraying in some starting fluid while cranking the engine. If it starts you have a fuel problem, if nothing then you have a spark problem (assuming you didn't blow the head gasket from overheating and was running normally before this happened).
Based on what you've already done here are my recommendations:
No spark: check ignition relay
No fuel: check fuel pump relay (aka shutoff relay, aka fuel pump shutoff relay), crank and cam position sensors, fuel filter.
There is also one other possibility, that the timing belt snapped. You would need to remove the timing cover to check this.

Feb 05, 2010 | 1995 Chrysler LHS

1 Answer

I have 97 chrysler lhs 3.5l that just died on me and wont start its getting fuel ive replaced the ignition coil and the cam and crank sensors but still wont start and am getting an cam sensor not giving...


I would check the timing belt probably broke. Best way pull the cam sensor out take a flashlight shine it down in the hole and have someone turn it over. u should see it turning if you don't the timing belt is broke. good luck

Oct 10, 2009 | 1997 Chrysler LHS

1 Answer

1996 Chrysler LHS not firing


First, check the ECM fuse in the power control module (it will be a yellow 20 amp fuse). Second, check the timing belt. You can pull out the cam sensor and look in the hole while someone cranks the motor. If the cam gear is not turning, the timing belt is broken. VERY IMPORTANT - when replacing the cam sensor, get a special adhesive pad from a Chrysler dealer that attaches to the bottom of the sensor to set the proper gap (cost about $2). Install the cam sensor until the pad touches the gear and tighten down the locking bolt. The pad will wear off in normal running. If the gap is not set correctly using this gapping pad, you won't start.

May 12, 2009 | 1996 Chrysler LHS

1 Answer

1994 Chrysler LHS Starting Problems


it's either a spark or fuel fault , if there is spark after it shuts down it is a fuel fault. connect a pressure gauge in the fuel line, start the engine , note fuel pressure around 35 psi , stop engine , pressure should drop a little then hold, if not check pump return valve and pressure regulator , check fuel flow , if low replace fuel filter,

May 05, 2017 | 1994 Chrysler LHS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...