Question about Jeep Wrangler

Open Question

Can't find the starter relay location in my 1993 jeep yj

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Mike258
  • 1498 Answers

SOURCE: YJ Blinker Relay

Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Posted on Aug 31, 2008

Ad
  • 337 Answers

SOURCE: where is the starter ignition

Front seating area, driver side, driver side of steering column, behind upper dash panel, mounted above fuse block

Posted on Dec 19, 2008

  • 6982 Answers

SOURCE: im trying to locate the starter for 1994 jeep grand cherokee , see if its easy to replace, and also the location of the starter relay

starter relay is in power distribution center near battery. don't know which engine you have, but if you flollow the positive cable on the battery, it will lead you to the starter. Most are not difficult to replace, depends on how much experience you have. One tip...dont overtighten wire connections on starter the solenoid cover is plastic and can break.

Posted on May 07, 2009

  • 6982 Answers

SOURCE: clutch pedal, starter, ignition... where is the

If you find the switch, you can temporarily jump across it, 'till you get a new one. When you go to buy it you are looking for a clutch switch.
Neutral switches are found on automatic trans vehicles. If you jump it out, be VERY careful to make sure you start in neutral with the clutch depressed as without the switch, it will start in any gear even with the clutch engaged.

Posted on Oct 29, 2009

wireguy212
  • 1627 Answers

SOURCE: how can i locate and test the starter relay on a

You don't need to.You need to put new contacts in the starter solenoid switch,just take the three 8mm bolts out of the solenoid cover and pull out the plunger and you will see what i'm talking about,the car has no relaly for the starter.

Posted on Nov 07, 2009

Testimonial: "Hey to wrirguy212 Thanks for your time! I am needing more details. starter/solenoid bench test good. parts store lists a starter relay mounted on fw"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter relay located on a 1993 jeep cherokee 2wd.


93 is first good year for all jeeps, lucky you are. YJ jeep.
which engine?
ask for help not parts, jeep.com parts online shows all parts so there is never a need to ask that.
ask why the starter is dead. (well what transmission) auto or stick?

no noise means NO CRANK, no engines un cranked but my M/T
fails hot and cold some times , good input , rare this. here.
and 2wd too boot, very rare this fact. stated.
ok.

when a car does not crank what do we do. (easy to hard just like AAA tow does)
  1. i wiggle key, at start position, crank now.?
  2. i wiggle the shifter, in park, and crank (PRNDL switch issues)
  3. same but move shifter to neutral, (keyon, foot on brake shift to neutral and crank, cranks now? neutral contacts good park bad.
  4. next if all above fails, (all free to do) we next check battery volts. 12.6vdc i good, 11v bad, charge it or get a new one.
  5. I then jumper cable jumper battery off runnning donor car, like AAA does. crank now? yes, battery has issues, common as nails that. No crank now, so.
  6. I then hot wire the starter soleniod. keys in pocket, it does not crank the starter is bad. it cranks now the key line is bad or

A real FSM book, online, and free.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

click 93 jeep, click wiring. pdf page 64 shows your relay.
see that the fuses need to be good
and the PRNDL switch energizes the starter relay.
the PRNDL ground the relay coil , the coil gets power from the Ign. switch and RELAY pin 29 goes to 12v cranking (11v typ) and the starter cranks.
that is how it all works.
if you have a volt meter all this is super easy, and no guessing needed. ever.
if you buy a new relay and it dont fix it ,you will be back here.

Feb 11, 2015 | 1993 Jeep Cherokee Country

1 Answer

Where is my horn relay located?


in most cars, if it even has one. is in the fuse box.
1993. first real chrysler car. and real engine controls by same with OBD1, good best older year car.
RTM read the manual yet?
the FSM
?
chapter 8G is HORN, and horn options.
page 2 covers the relay test.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

chapter 8w-11 show the fuse box. and relay , clear as day
YJ is pdf page 90 (wiring)
XJ is pdf 165, dual horns.



Sep 17, 2014 | 1993 Jeep Cherokee Country

1 Answer

1993 Buick Park Avenue starter relay location


The solenoid is located in the starter, I don't know any other relay for the starter

Mar 24, 2013 | 1993 Buick Park Avenue

1 Answer

1993 jeep wrangler yj speedometer and odometer do not work


first check your fuses, then if thay are fine and veh has a veh speed sensor vss, it may have a bad connection, or the sensor may be bad, (located on the transmission)

Aug 26, 2012 | 1993 Jeep Wrangler

1 Answer

How to step by step guide on replacing starter in 1993 ford jeep wrangler yj 4x4


well im not sure that the Ford part is.. but on your YJ its pretty simple, 1.disconnect the battery 2,disconnect the power leads to the cylanoid (its mounted to the top side of the started) 3.remove the starter mount bolts and slide the started our of the transmission Note: sometimes its necessary to remove the mount bolts and and remove the starter from the transmission in order to gain good access to the power wires. you can either have a partner hold the starter for you once its loose or use a bungee cord to tie it up while you disconnect it. 4. installation is reverse or removal Note: on re-manufactured starters it may be necessary to shim the starter. if after installation it grinds on the flywheel then you know it needs to be shimmed, most re-mans will come with a set of shims. hope this helps, and for the record most men who think they know alot about cars or talk like they do dont know jack diddly. i know a couple women who are fantastic mechanics.

Mar 13, 2012 | 1993 Jeep Wrangler

2 Answers

Which of the relays is the starter relay on a 1993 Dodge Caravan


there isn't a starter relay, there is a solenoid on the starter itself

Sep 22, 2011 | 1993 Dodge Caravan

1 Answer

The fuel pump doesnt come on and there is no spark.....


Check for the fuse for the fuel pump and the relay. Other than that it may be a wiring issue or a computer module issue.

Dec 13, 2009 | 1993 Jeep Wrangler

3 Answers

Ignition on jeep yj will not start engine. all


Before blaming the starter make sure the battery is fully charged. It should be around 13V.
Starter circuits for the most part operates in the following way. Turning the ignition key supplies power to a relay situated in the engine compartment which in turn activates the solenoid on the starter which powers the starter itself.
Make sure your vehicle is in Neutral(Manual gearbox) or Park(Auto box) Locate the starter motor. On the starter there is another cylinder like object called the solenoid. There is a thick red wire running from the battery connected to this. There is also a much thinner wire which activates the solenoid. To test the starter run a wire from the + on the battery to where the thin wire connects on the solenoid. (ignition must be off) This should activate the starter and turn the engine. If nothing happens the starter is probably at fault. Before removing the starter make sure that the engine is properly earthed as this could also give problems.
If the starter does kick in the problem is further "upstream" Most probable cause would be the relay. If you can locate it, replace since it is relatively cheap.
Starter repair is best left to the experts. Get a quote for a new starter before you have the old one repaired. You'd be surprised at how many times it turns out that replacement costs the same as repair.
Let us know if you've solved the problem.

Dec 09, 2009 | 1994 Jeep Wrangler

1 Answer

Soft top-1993 Jeep Wrangler YJ


OK I have a yj and you start from the windshield put the snaps/or what ever yours is on the top of the doors then down the side or the doors then under the back side window then around the curve and this is the hardest part then your tailgate also make sure your bars on the inside are loseuntil the top is on then thighting those bars and you should have a nice tight top but belive me it is hard and you might need a flathead screw driver for the corners. Good luck and a jeep wave to you!

Apr 03, 2009 | 1993 Jeep Wrangler

1 Answer

93 wrangler yj electrical wet


You have likely fixed this by now but if not, you will have to use some dry rags and dry off everything!!!! Use compressed air wherever you can't get to (or at the least, a tire pump) Vehicles are not designed for use in the water. If ;you want to do this, get with some off road clubs that can give you tips on waterproofing stuff!!! Just to somewhat "wheatherise" my stuff, I wipe down ignition components with a rag saturated with wd40&silicone spray. I don't think this will work in deep water but it sure helps in very damp or rainy weather! You can also make splash guards out of very heavy tar paper or sheet metal that you can place under the front, but be careful where and how you place and secure it so nothing interferes with steering etc.

Feb 18, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...