Question about Cars & Trucks

Open Question

Axle nut torqe specs for 2004 nissan titan front

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 99 Answers

SOURCE: What are the torque specs

the torque are not mention out side any authorised workshop for that you need to visit the nearest authorised dealer or service centre & leave the rest of work to them without any hazard or trouble or either can start from a torque of 25 to 45 lbs. do not exeed the limit or other wise the nut or even the Axel can get broken in the prossess of facinating it so till then my friend have happy motoring & see you soon.!

Posted on May 08, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

tneubauer
  • 437 Answers

SOURCE: Torque Specifications

1. If you are speaking of the large yoke nut there is no "torque spec" per say, instead it is a rotational preload-

From Ford manual:
Use the special tool to hold the pinion flange while tightening the nut to set the preload.

  • Tighten the nut, rotating the pinion occasionally to ensure the differential pinion bearings are seating correctly. Take frequent differential pinion bearing preload readings by rotating the pinion with a Nm (inch-pound) torque wrench. The final reading must be 0.56 Nm (5 lb-in) more than the initial reading taken during removal.
2. If you are looking for the yoke straps that hold the universal in place to the yoke it is 14ft lb for the 4 bolts.

Posted on Jun 01, 2009

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the passenger side front axle?


remove passenger side wheel remove center nut on axle shaft i believe a 33 mm remove cotter pin on lower ball joint remove nut on lower ball joint with a ball joint seperating tool(pickle fork) seperate lower ball joint might need to tap axle shaft out of the wheel bearing pull the whole assembly aside where the axle goes into the transmission use a pry bar and pry out on the axle sometimes are stuck in pretty good then reverse the procedure to install be sure to torqe axle nut to specefications
good luck chris

Mar 09, 2011 | 2004 Pontiac Grand Am

1 Answer

Axle nut torque specs 2004 escape


Front axle nut torque is 300Nm or about 220 ft-lbs.

Sep 08, 2010 | 2004 Ford Escape

1 Answer

My brake, slip and VDC indicators stay on.


Check brake fluid level, add fluid from sealed container if needed.

Also check for leaking rear axle seals. Look for oil on the inside of rear wheels.

May 06, 2010 | 2004 Nissan Titan

1 Answer

Torque spec for 2004 vibe front axle nut


Hello there is no specific torque on this nut torque it witch an inpact tool or a long bar and make sure to locked it witch a cutter pin or if there are a recess in your axle punsh the nut in the recess witch a punh.

Mar 08, 2010 | 2004 Pontiac Vibe

1 Answer

I have a 1996 olds cierra. Need a torqe spec on front axle. Replacing a wheel bearing. Thanks!


Hello Quiggle.
The axle nut torque is a 107 ft lbs according to the service manual.
Thank you for using FixYa !

Dec 03, 2009 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Need torq specs and sequence for cam jornal caps for a 5.6 nissan titan motor 2006


Could not find specs for 2006 but this is the specs for 2005 5.6
  • Step 1: Bolts 9-12: 17 in. lbs. (1.9 Nm)
  • Step 2: Bolts 1-8: 17 in. lbs. (1.9 Nm)
  • Step 3: All bolts: 52 in. lbs. (5.9 Nm)
  • Step 4: All bolts: 92 in. lbs. (10 Nm)
  • Tighten front cover bolts to 8 ft. lbs. (11 Nm)
  • Nov 11, 2009 | 2005 Nissan Titan

    1 Answer

    The rotor on passenger side wil not come of do i need to removed the cotter and axle nut


    Take a block of wood on either side on the rotor and smack it with a hammer.It should break loose.Careful not to hit the studs maybe putting on the lug nuts before hitting..You may have to hit it hard...

    Mar 30, 2009 | 2004 Nissan Titan

    1 Answer

    2005 chevy 4x42500hd


    Hi..
    On your 05 Chevy 4X4 2500HD.
    The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

    I hope this help on your question.

    Thank you for use fixya...

    Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    80 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...