Question about 2007 Subaru Forester 2.5X L.L. Bean Edition

Open Question

Subaru forrester brake rotor thickness

Brake rotor thickness

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: how much should brake repair be for a 1999 Subaru

Best thing to do is get on the phone and call an auto parts store and get a price on the parts you want to replace, than bump that up about 10% more or less witch is most likely a shop will do, and then take that and add the labor, witch averages around 60 to 70 bucks per hour at a independent shop and 80 to 100 bucks per hour at a dealer. They will chg. at least 4 hours. remember this is only a gessament and everyone chg. different, but its someware in the ball park. Depending on what the parts cost 500 to 600 dollars is not out of the realm of posabilitys. whole lot cheaper if you do it yourself.

Posted on Apr 12, 2009

  • 270 Answers

SOURCE: For 2001 Forrester Subaru - Front Windshield Washer fuse

If it makes noise, it's not the fuse. Most likely the discharge nozzles are stopped up. Try blowing compressed air into them from the outside.

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Brake disc limit

The minimum rotor thickness is normally cast into the rotor. You will find it printed either on the outside hat section of the rotor or on the very top edge section of the rotor.
There are some example pictures here

Apr 19, 2016 | Cars & Trucks

1 Answer

Severe wheel wobble when braking on steep decents

It is not wheel wobble but vibration from the front brakes. The front brake rotors have worn unevenly (known as disc thickness variation - DTV) and when this occurs you will get vibration from the front rotors as you apply the brakes and it is especially noticeable when braking on down hill runs. DTV is usually caused by poor alignment of the rotors on the hub. In other words sloppy installation procedures.

You will need to replace both the rotors and brake pads on the front and make sure the business that does the work properly checks the rotor for run out.

Disc Thickness Variation DTV Issue 14 Bendix Brakes

DTV Disc Thickness Variation Disc Brakes Australia


Feb 21, 2016 | Cars & Trucks

1 Answer

Minimum thickness for buick lesabre front rotors

Hello there
From a kind chap on this page

For a 2000 Buick LeSabre


Discard Thickness30.7 mm (1.209 in.)
Lateral Runout (New)0.06 mm (0.002 in.)
Minimum Thickness after Refinish31.08 mm (1.224 in.)
Rotor Diameter 15 inch Wheels (New)278.0 mm (10.9 in.)
Rotor Diameter 16 inch Wheels (New)303.0 mm (11.9 in.)
Rotor Thickness (New)32.20 mm (1.267 in.)
Thickness Variation (New)0.025 mm (0.001 in.)

Sep 15, 2014 | Buick LeSabre Cars & Trucks

1 Answer

Minimum rotor thickness

I don't know the min thickness, but I have an outback just like yours and if there is a problem with uneven rotors it's usually cheaper and easier to buy aftermarket at NAPA auto or other supplier (shop around) and trash the old rotors. If the rotors can be turned then keep them for the next brake job and use them then. Outbacks are easy to do about 30 min a side rotor and pads after the wheel is off, just did mine.

Sep 03, 2014 | 2010 Subaru Outback

1 Answer

Avalanche minimum rotor thickness

Rear Brakes JC5/JH5 Utility Only
Rotor Discard Thickness* .............................. 28.50 mm (1.122 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 29.0 mm (1.142 inch)
Rotor Thickness-new .................................... 30.0 mm (1.181 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Rear Brakes JH6
Rotor Discard Thickness * ............................. 27.50 mm (1.082 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 28.0 mm (1.102 inch)
Rotor Thickness-new .................................... 29.0 mm (1.141 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Nov 12, 2013 | 2002 Chevrolet Avalanche

1 Answer

Replacing front shocks on a subaru forrester 06 model

go to and translate the website amazing with your browser and fix it.

God bless you

Jul 08, 2013 | Cars & Trucks

1 Answer

Minimum thickness for a 1997 toyota avalon front rotors

lordFord's answer was arrogant and absolutely useless. Brake rotor thickness specifications are dependent upon the Year/Make/Model of the vehicle, it has nothing to do with your "state/province" or "common sense." Most brake rotors have the minimum thickness spec. stamped on the rotor itself. The service department of the dealership for whatever brand of vehicle you have, will be able to provide the spec. to you as well. A visual inspection may point to obvious signs such as scoring, cracks or pitting, and a vibration when applying the brakes, could be a warped rotor.

Jul 27, 2012 | 2003 Oldsmobile Alero

1 Answer

What is minimum brake rotor thickness for the front and the rear?

All are different, on the back side of the brake rotor , will have a stamp with (MIN) and some number after it the will be the minimum spec thickness for the brake rotor.

Dec 02, 2010 | 2007 Chevrolet TrailBlazer SS

2 Answers

04 subaru impreza.frontend shimes at higher speeds when brakes are applied

Front Rotors need to be turned or replaced. Good Luck!!!

Nov 14, 2010 | 2005 Subaru Outback

Not finding what you are looking for?
2007 Subaru Forester 2.5X L.L. Bean Edition Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides