Question about 2006 Nissan Sentra
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
all you have to do is inspect the old trunk door how it is attached to the hinges.
be careful on the tension bars that are lifting the trunk. once you released them, the trunk would just fall down.
there are two of these tension bars, they are like springs to help you lift the trunk and they are very tricky to remove and install
after you have done that then it just a matter of removing 2 bolts on each side of the hinge and remove the trunk.
if you have electrical accessories attached to the trunk such as solenoids or trunk cables, remove them first.
then do the reverse on installation.
you may want somebody helping you hold to the trunk before you remove the bolts. they are heavy.
tnx 4 using fixya,
Posted on Sep 14, 2008
I assume you are talking about the outter tie rod.
Jack up and support the car and remove the wheel.
Then you see the tie rod. Their is a lock nut agenst the tie rod. Break this nut loose. It is normally a 17-21mm nut.
Now remove the cotter pin (if applied)and break loose the castle nut.
Now use a ball joint splitter or a tie rod splitter and pop the tie rod out of the knuckle.
DO NOT HIT THE KNUCKLE WITH A HAMMER. If memory serves me this car has a aluminum knuckle and if you can damnage it if you hit it with a hammer.
Now just spin the tie rod off and install the new one.
Take it to your local shop to have the alighnment done.
Posted on Dec 10, 2008
it should be underneath your car in between the firewall and the engine. Now you don't want to supply direct power to your starter because you'll end up frying it. However to just start the car once you've located the starter, get a long screwdriver with a plastic handle and connect the two wires with the screwdriver.
As for a long term fix, without investing the money to replace the necessary parts. You will need to attach a wire that can handle 12v to both wires on your starter separately. Then connect the other ends of both wires to a switch that can handle 12v, and mount that in your car somewhere. Then whenever you need to start your car just flip the switch on until the car starts then once it is started flip it back off.
I know this sounds like a lot but it is very doable with about $5 and a little bit of time.
Posted on Jan 30, 2009
Always you can search the web, especially Google (Image).
And Google Web.
If you can access the web it's very easy to learn how to fix, repair or overhaul your things (cars, trucks, components, etc.).
Just write your questions like below;
How to replace 2001 Nissan Sentra starter location?
then you'll find a lot of answers.
See the below RH side of the pic is the starter.
See; this site,
See; And search the bottom site.
Graphics Used On The Auto Repair - About.com
Index To Illustrations.
Posted on Jun 02, 2009
Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
Install or connect the following:
Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.
Posted on Jul 31, 2009
Tips for a great answer:
Jun 15, 2012 | 1996 Nissan Sentra
May 22, 2012 | 2002 Nissan Sentra
Apr 02, 2011 | 1994 Nissan Sentra 4-Door
Jan 21, 2011 | 2006 Nissan Sentra
Jan 20, 2011 | 2006 Nissan Sentra
Jul 14, 2010 | 2006 Nissan Sentra
Dec 29, 2009 | 2006 Nissan Sentra
Aug 03, 2009 | 2001 Nissan Sentra
Jul 31, 2009 | 2005 Nissan Sentra
188 people viewed this question
Usually answered in minutes!