Question about Chevrolet Uplander LS

Open Question

2007 uplander - hard to find oil leak near oil filter housing. any ideas?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 Murano has an oil leak near the oil filter

The oil filter mounts on an oil cooler housing that has an o-ring on the block side of it. The housing is held in place by the double ended connector bolt that the oil filter screws onto one side and the other goes into the block. This should be tighten to 37 ft/lbs. prior to installation of the oil filter. It may be loose or the o-ring might need replacement.

Posted on Apr 16, 2009

  • 100 Answers

SOURCE: 2007 Jetta 2.5L: how to change oil filter

Usually with draining the oil filters you just screw it off and the oil will drain. It can sometimes be messy but thry to keep your arm out of the way and have the oil pan at the bottom. If some gets on the engine or header pick up some break clean and spray off the remaining oil that made a mess and it should come all clean like you didn't even spill any oil!

Good Luck!

Posted on Aug 13, 2009

thefazool
  • 3 Answers

SOURCE: Oil leaks from the oil filter adapter

If it is not the suggested gasket that is leaking then it is the oil pressure switch located exactly above the oil filter adapter. The black plastic housing could have developed a crack and oil will ooze downward and drip off the bottom of the adapter. I had this problem and changing the oil pressure switch took care of it.

Posted on Dec 18, 2008

MEGA_MUZIK
  • 54 Answers

SOURCE: 1996 Honda Accord 2.7L/V6 oil leak near oil filter/oil switch

my car was doing the exact same thing and i spent about 18 hrs total trying to figure out. if you remove the oil filter, you will notice that the "bracket" that the oil filter attaches to is removable. remove the ENTIRE oil filter assembly. there is a bolt almost behind the crank pulley, its tricky to get to but you can get to it with a 1/4 in drive, swivel, and extension, i do believe it was a 10-12 mm socket (MUST BE ^POINT SHORT WELL) the top left bolt on the assembly you will notice that you can not get out. that is fine, take the rest of the bolts out and let the assembly hang from that bolt, BUT the bolt must me loosend all of the way to achive play in it. take a small screw driver and "break" the seal on the assembly. you will notice 2 holes. around those two holes is a single gasket. even the smallest crack will aloow oil to drip. my car was using about a gallon of oil every ten miles, so you can imagine how much oil i when through, replace the gasket. You can not get the rubber gasket ANYWHERE except a honda dealer. replace. put it together and you all set.

BASIC STEPS: RAISE PASSENGER SIDE.
REMOVE TIRE
REMOVE OIL FILTER
REMOVER ASSEMBLY
REMOVE GASKET
AND REPEAT BACKWARDS FOR INSTALLATION

Posted on Oct 26, 2009

  • 247 Answers

SOURCE: Need to remove oil filter housing - oil leaking

This is not an easy repair in your driveway, but can be done. 1st thing, have you checked to see if the oil filter is the issue or is it the drain plug? If its the oil filter housing gasket, you will need to remove the filter. The housing is held in place by the threaded bolt assy that the filter screws onto. You will need to remove that bolt, remove the coolant hoses. Clean the engine block surfaces, for the new gasket to mate to, clean the cooling housing surfaces, install the bolt through the housing, and install the gasket onto it. Then install the bolt/housing into the block and tighten the bolt. Install the coolant hoses, oil filter. Fill the cooling system with the coolant that you removed. Fill the engine with oil, start and check for leaks.

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ECM on a 2007 Chevy Uplander located?


Located under the hood in the black box opposite the air filter housing.

May 09, 2015 | 2007 Chevrolet Uplander

1 Answer

2007 chevy uplander leaking oil from top of oil filter why how do i fix it ?


Make sure the oil filter does not have a double gasket. If the oil filter was changed and the old filter gasket stayed in place the new filter and gasket will not seal

Apr 12, 2015 | Cars & Trucks

2 Answers

WHY CHEVY UPLANDER 2007 STERRING IS HARD TO TURN LEFT AND RIGHT


How hard, if it's as if you have lost power steering. Check to see if the power steering belt is still there or slipping, power steering fluid is low or empty. (Is cap leaking or leak in hose)
if it still has has power assist and has just gotten harder is it all the time or just low idol, need a better description of what is happening , I hope this helps

May 29, 2014 | 2006 Chevrolet Uplander

1 Answer

Oil leak in 99 vw passat oil filter housing


Its a pretty easy fix with a litttle mechanical ability. Just remove filter,remove filter base/ oil cooler, replace gasket

Mar 04, 2014 | 1999 Volkswagen Passat

1 Answer

2007 uplander oil pressure switch


located on the block by the oil filter

Mar 21, 2013 | 2007 Chevrolet Uplander LS Minivan

1 Answer

Want to replace transmission filters on 2007 chevy uplander


My 07 uplander jerk hard into gear when I take off from a dead stop is it because my transmission is over filled

Jul 23, 2012 | 2007 Chevrolet Uplander LS Minivan

2 Answers

Oil leaking around or near the oil filter


Might have to take the filter off wipe the O-ring thats on the filter clean and the area where the filter will be going on to the block. Probably has some dirt where the filter seats on the block.

Feb 09, 2010 | 2005 Ford Escape

3 Answers

1996 Honda Accord 2.7L/V6 oil leak near oil filter/oil switch


my car was doing the exact same thing and i spent about 18 hrs total trying to figure out. if you remove the oil filter, you will notice that the "bracket" that the oil filter attaches to is removable. remove the ENTIRE oil filter assembly. there is a bolt almost behind the crank pulley, its tricky to get to but you can get to it with a 1/4 in drive, swivel, and extension, i do believe it was a 10-12 mm socket (MUST BE ^POINT SHORT WELL) the top left bolt on the assembly you will notice that you can not get out. that is fine, take the rest of the bolts out and let the assembly hang from that bolt, BUT the bolt must me loosend all of the way to achive play in it. take a small screw driver and "break" the seal on the assembly. you will notice 2 holes. around those two holes is a single gasket. even the smallest crack will aloow oil to drip. my car was using about a gallon of oil every ten miles, so you can imagine how much oil i when through, replace the gasket. You can not get the rubber gasket ANYWHERE except a honda dealer. replace. put it together and you all set.

BASIC STEPS: RAISE PASSENGER SIDE.
REMOVE TIRE
REMOVE OIL FILTER
REMOVER ASSEMBLY
REMOVE GASKET
AND REPEAT BACKWARDS FOR INSTALLATION

Jul 13, 2009 | 1996 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,608 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...