Question about 2005 Chevrolet Colorado

Open Question

Clutch problems internal slave cylinder - 2005 Chevrolet Colorado

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hank5899
  • 151 Answers

SOURCE: 97 chevy cavalier 2.2l 5sp clutch problem

get the hyd clutch system assembly complete and pre-bleed from the dealer

Posted on Sep 07, 2008

  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

motor1258
  • 6674 Answers

SOURCE: 1994 chevy camaro 3.4manual 5 speed

You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Posted on Jan 31, 2009

co7196
  • 3433 Answers

SOURCE: CLUTCH LINE LEAK AT HOSE FITTING AT SLAVE CYLINDER

Use a copper washer like on the brake lines, not an o ring.

Posted on Jun 02, 2009

  • 145 Answers

SOURCE: after replacing starter and removing slave cylinder, clutch fails to work

sounds like you have a air pocket or you fail to engage the slave cylinder push rod If you disconnected the slave cylinder from the hose proceed to bleed out the slave cylinder if you didn't take you slave cylinder and whit out disconnecting the hose and make sure the push rod is against the clutch push arm.

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont go into gear while driving has to be turned off then it will has new clutch


It sounds like the clutch is not disengaging when depressed. What is the year make and model? It most likely has a hydraulic clutch. Many vehicles have the clutch slave cylinder inside the bell housing of the transmission. This means that the fluid line to the slave cylinder was removed to remove the transmission. If a new slave cylinder was installed when the clutch was replaced (this is a good idea to do when servicing a clutch with a bell housing internal slave cylinder) then the system will need to be bled to remove air from the system and allow the clutch disengagement to function properly.

Mar 07, 2017 | Cars & Trucks

1 Answer

I have a 1989 Ford BroncoII 2wd clutch will not engage replace the slave cylinder master cylinder bled the clutch still won't engage. No air in clutch whatsoever. anyone have an idea?


Can you see the slave cylinder moving when the clutch depressed. If so, problem most likely internal to clutch. Possible broken shift fork... seized throw out bearing..... damaged pressure plate.... worn out clutch disc. The tranny will have to be removed for inspection

Nov 15, 2015 | Ford Cars & Trucks

1 Answer

Hydraulic leaking


Do you have a hydraulic operated clutch? The slave cylinder for a hydraulic clutch would be on or sometimes inside the bell housing. Some ford and chevy trucks put the slave cylinder in a very difficult to reach place-the transmission has to be removed to service the slave cylinder. Most cars have the slave cylinder mounted on the outside of the bell housing. If they leak, replace or rebuild, although those internal slave cylinders I think can only be replaced.

Dec 31, 2013 | Cars & Trucks

1 Answer

I have a 2000 mazda 323 with a manual transmission. i have already change the clutch kit but the gear is still hard to shift


Check the hydraulic clutch operation. This is a clutch master cylinder with a reservoir on the firewall, and a clutch slave cylinder down on the bell housing of the transmission, with a steel tube running from the master to the slave cylinder. When clutch pedal is depressed, hydraulic fluid (brake fluid) is forced from the master to the slave. The slave cylinder should push out a little plunger that contacts the clutch fork lever-pushing it forward to engage the clutch.
Add brake fluid to the reservoir if needed. Watch the plunger on the slave cylinder: if it moves little, or not enough, try bleeding the slave from the bleeder valve. They are bled just like brakes. If bleeding doesn't help, your clutch master or the slave may need replacing. The master cylinder, like a brake master, has internal seals that hold hydraulic pressure, so force can be applied to the plunger on the slave cylinder.

Dec 09, 2013 | Mazda 323 Cars & Trucks

1 Answer

Where is the slave cylinder for the clutch located. internal or externaly.


First thing to do is to see if you have a clutch slave cylinder or cable operated clutch. Second the slave cylinder is on the end of the lever that goes into the clutch housing Before you change the clutch make sure that the problem is not in the slave cylinder or clutch master cylinder or cable as the case may be.

Jun 09, 2013 | 1998 Dodge Avenger

1 Answer

How far does the slave cylinder on a 99 ram 2500 diesel have to travel to disenguage the clutch?


might just need bleeding through more , check for any leaks etc on all connections,pipes etc

Jun 02, 2017 | Dodge Ram 2500 Cars & Trucks

1 Answer

How do i tell if my 1995 slave cylinder is internal or external


slave cylinder is at wheels or brakes most are internal meaning you have to remove brake drum to access them .slave cylinder on clutch usuall external

Feb 14, 2011 | 1995 Chevrolet Cavalier

2 Answers

Having problems with the clutch in my 1998 Ford Ranger. There is no freeplay, and it is very difficult to shift. Do I need to adjust the clutch? If so, how do I adjust it?


The clutch is not adjustable,it is a fluid clutch.It has to be a leak,or the slave cylinder,and,or, the master cylinder are bad,It does not have to be leaking to be bad,but it is one of the two.Rate please,thank you.

Jul 12, 2010 | 1998 Ford Ranger SuperCab

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...