Question about Ford Ranger

Open Question

Wl 2.5 t engine torque settings in Nm for cyl head and mains+big ends+ valve clearance

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

Ad
  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

  • 34 Answers

SOURCE: Cyl. head tightening torque and sequence for a

The online manuals are a super help. I use them all the time. http://www.autozone.com/autozone/myzone/profile/membershipBenefits.jsp

Posted on Oct 14, 2009

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Zim1308
  • 543 Answers

SOURCE: 4bc1 engine torque settings, al settings requirred

This is a really long list and will be difficult to satisfy, but there is help. You can go to your local parts store and purchase a Haynes manual, it contains all the specifications and steps for rebuilding a vehicle of your choice, they are accurate and helpful. with a lot of illustrations and written out steps for any and all procedures.

Posted on Jun 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the tappet clearance and torque setting for hyundai atos 1.1 2007


valve clearance is inlet .02mm hot. exhaust .025 mm hot cyl head torque is cyl head torque stage1 30-35nm stage2 60-70nm stage3 run engine for 15 minutes. stage 4 tighten further 70-75 nm

Dec 15, 2016 | 2007 Hyundai Atos 1.1

2 Answers

I need the big end torque on the Rocam engine please


A cheap shop manual will have this and much more. If you are in this deep you probably need one.

Sep 05, 2016 | 2000 Ford Ka

1 Answer

I want to know the torque specifications for a 4D32 mitsubishi engine ?


we have 4g32 cyl head stage 1 70-76 nm stage 2 run for15 mins stage 3 tighten 78-83 nm
main bearings stage1 24-27 nm
stage2 49 -54 nm
big end stage 1 15-17 nm stage 2 31-34 nm I hope this helps from Coloneus

Jun 07, 2016 | Mitsubishi Cars & Trucks

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

Torque settings


depends on your engine. If it's a VW air cooled flat 4, the mains which also ties down the engine casings, is torqued to 35 ft lbs and the cyl heads to15 ft lbs.
On more modern engines the mains can be torqued to 65 ft lbs, the big ends to 45 ft lbs and the cyl head to anywhere between 30 to 45 ft lbs.
A common remark among mechanics is to turn them till they strip, then a quarter turn back. Don't follow this rule.

Nov 05, 2014 | Cars & Trucks

1 Answer

Help with torque setting for mazda b2500 wl diesel engine


What is de torque for wl 2500 mazda main bering. Thanks

Mar 25, 2013 | Cars & Trucks

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

3 Answers

Hello,I am overhauling a 4hf1 engine and need torque-timing and other calibration specifications.


Main bearings - stage 1-80 Nm; stage 2-100Nm.Big ends-stage 1-22Nm,stage 2 -45Nm.Flywheel/drive plate-55Nm.Crankshaft puley-120Nm.Cil.head as main bearings.Valve clearance - cold - inlet-0.15 , exhaust - 0.25. Timing 6/800 at sea level.Good luck!

Nov 28, 2009 | 1995 Isuzu Pickup

1 Answer

Head stud torque


cyl head torqes.1st stage 29 nm. 2 nd stage 57-67 nm. 3rd stage slacken off 360 cegrees, 4th stage 29 nm. 5th stage 64-74 nm. intake and exhaust valve clearance .38 mm hot setting. hope it goes ok.

Aug 14, 2009 | 1987 Nissan King Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...