Question about 1994 Toyota Pickup

Open Question

Seat belt on 1994 toyota small pickup will not retract drivers side

THE SETBELT IS PULLED ALL THE WAY OUT . THE RETRACTOR WILL NOT ROLL IT BACK UP. NEED TO REPAIR . A NEW ONE IS 190.00 BUCKS THAT I DO NOT HAVE. THANKS

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: Seat Belt will not retract on 98 Pre Runner

When you replaced the belt did you make sure that the position of the belt assembly was the same. A slight misaliengment can affect the return mechanism. Pull the full length of the belt from belt coil Slacken the securing bolt moving the assembly will most likely allow the return of the belt.
If it was an old unit perhaps a drop of WD40 will release the mechanism.
Hope this helps
Mic

Posted on Jun 09, 2008

  • 1861 Answers

SOURCE: 2002 Toyota Solara Convertible seat belts not retracting

The front seatblet retractor springs have weakened. Unfortunatly, there are no "user serviceable parts" on them. They would have to be replaced. How many miles is on it? If you have low mileage, the Toyota Customer Experience Center may provide you some assistance, as the belt replacements are quite expensive. I'd call the CEC and explain your dilemma. Here is the number: 1-800-331-4331

Posted on Sep 23, 2008

  • 1 Answer

SOURCE: 99 Toyota Camry one of the rear seat belts won't retract

You have to actually unbolt the belt holder behind the seat. Then from there you can check to see if the spring still works. You'll probably have to take the cap off it, wind the spring-load, then put the cap back on. If you can get to it, it's not too difficult. I recommend another pair of hands to help hold if they're available. You'll also want to make sure you've rolled the belt up as much as possible before before you coil the spring-load.

Posted on May 14, 2009

flbergeron68
  • 541 Answers

SOURCE: driver side seat belt retractor broke. how to fix?

yes you can. I suggest you go to the scrapyard and purchase one there. they are easy to replace and inexpensive.

Posted on Jul 09, 2010

ginko
  • 19396 Answers

SOURCE: Where is the seat belt

Hi.

The retractor motor is located inside the retractor. The retractor is located aside the seat, in the internal chassis. The retractor is where the belt folds in.
The retractor motor is present only if you have electric-retraction seat belt. Standard feature on this car was a mechanic retractor based on a spring system.
If the retractor motor is present, it will be located inside the belt retractor. To access it you need to remove the belt trim cover held by tabs,
If motor is present, this can be tested energizing directly its contacts. This is done connecting the motor to powered wires and observing if it runs. If the motor is OK, then the electric belt system uses also a solenoid and a control module located under the dash.

With or without motor, the retractor is quite difficult to reassemble. Do not disassemble if not necessary.

Regards.

Ginko.

Posted on Apr 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The drivers side seat belt on my 90 Honda prelude will not retract at all


Damaged retractor on some vehicles when the seatbelt retractor gets damaged. Either by getting in a crash or in some cases a hard stop when the belt is worn by someone it will not retract

Apr 20, 2015 | 1990 Honda Prelude

1 Answer

My passenger side seat belt on my 2000 ford taurus se is locked and i cant retract it. how do i fix this problem with buying a new seat belt retractor


of course it possible to access this retractor , you just need to locate the small round circles in the lower part of trim and gently pry the covers off , screws will be evedent , you will need a 6 mm star (five sided) drive socket wrench to remove the retractor though

Feb 10, 2015 | 2000 Ford Taurus

1 Answer

2008 chevy uplander seat belt wont retract how do i fix it


Please check if your seat belt has "Retractors" or "Automatic Retractor".

Follow these steps to determine if you have a retractor system that will hold car seat securely or your seat belt won't retract as should be:

A. Pull belt all the way out.

b. Allow belt to retract about 6 inches (15 cm).

c. Pull out on belt again.

If belt is locked and you cannot pull the belt out any further, you have an Automatic Locking;

If you pull the belt again all the way out and won't return to normal operation, then the mechanism is damaged, but try first the "retractor" lock to be sure. By Federal Law, nobody will sale a seat belt in a junk yard, try the dealer or order thru the dealer the whole seat belt or the mechanism. I hope that is just a matter of the automatic retractor; you can see this information in your car's manual. Try and we will see.

Jul 02, 2014 | 2005 Chevrolet Uplander

1 Answer

Air bag code 33 for a 2005 lincoln town car


2005 Towncar SRS Code 33 (3 flash + 3 flash, repeat this set for twice. then Beep 5 times pause x 5 = 25 beeps every 30min).

This means you have problem with left (Driver) side pretentioner (Seat belt retract system).
It doesn't mean physical belt or retract mechanism.It is just bomb wiring which is part of airbag system.
When airbag deploy, passenger must stay tight in seat otherwise body lean to front then slam back to seat by airbag.
if belt is loose or delay to lock, passenger's body rocks back and forth.So, system use small bomb (Fire power) to lock and retract seat belt when airbag deploy.There is small bomb and igniter in part of Seat belt retractor.
Code 33 is warning for this part on 2005 Towncar.(older model is different meaning in Ford/Lincoln, it's possibly passenger side airbag system for earlier model)
Before you work for any part of Airbag system and touch any "Yellow connector", * *Disconnect battery (negative side is good enough) and wait at least 5 min to clear all power in system**.(Airbag store back up power for few minutes to be able to deploy even in case if power disconnected)
by the way, you should move your driver seat most forwarded position before you disconnect battery to make it easy to work with seat belt.
locate driver side seat belt retractor (in center pillar between front and rear door, you may have to fight with weather strip)

Locate Yellow connector on bottom of Seat belt retractor (it's called "Pretensioner")it is located on very bottom of rear side of retractor.
only one yellow connector. (make sure your battery is disconnected)
Check its physical connection or looseness.if connection looks fine, you may have to replace whole seat belt ($180-$200 in Lincoln dealer)
You can check if pretensionor is good or bad by regular tester, but unless you know how, I won't tell (because I don't wan't you to blow out pretentionor).








Jul 19, 2012 | 2005 Lincoln Town Car

1 Answer

2002 Mazda Protege5. While changing rear struts, the rear seatbelts had to be unmounted. I allowed the seatbelt to retract and now it will not extend (only retracts/takes in) far enough to mount it back....


Hi, these retractors or sensitive to direction so that if the are not sitting properly they will not release. as if in a roll over situation. try holding the retractor at the angle at which it was mounted and then apply slight tension on the belt pulling out. Don't take the plastic covers off or the spring inside will come a part and you will be buying new belt assembly's

Aug 27, 2010 | 1999 Mazda Protege

1 Answer

Driver side seat belt retractor broke. how to fix?


yes you can. I suggest you go to the scrapyard and purchase one there. they are easy to replace and inexpensive.

Jul 09, 2010 | 1994 Toyota Corolla

1 Answer

Seat belts are not working


Driver side has a broken clock spring, you will have to replace the whole retractor because you can not just replace the spring. Nick

Apr 22, 2009 | 1998 Toyota Camry

1 Answer

How do we fix front passenger side seat belt retractor on 1999 Ford Taurus? It will not pull out....


you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:
  1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
  1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
  1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
sxh~us~en~file=ani_caut.gif~gen~ref.gif WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

Apr 21, 2009 | 1999 Ford Taurus

1 Answer

2002 Toyota Solara Convertible seat belts not retracting


The front seatblet retractor springs have weakened. Unfortunatly, there are no "user serviceable parts" on them. They would have to be replaced. How many miles is on it? If you have low mileage, the Toyota Customer Experience Center may provide you some assistance, as the belt replacements are quite expensive. I'd call the CEC and explain your dilemma. Here is the number: 1-800-331-4331

Sep 22, 2008 | 2002 Toyota Camry Solara

Not finding what you are looking for?
1994 Toyota Pickup Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...