Question about 1996 Ford F150 Regular Cab

Open Question

How to replace harmonic balancer in 2006 ford explorer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1992 ford tempo 4 cyl

I had this same problem a while back, water pump... replaced the water pump and all was well. If you run it for very long without you'll kill it. Hope this helps, KJS

Posted on Oct 05, 2008

  • 2 Answers

SOURCE: HARMONIC BALANCER

I have a '94 Tempo, it had a "ticking" sound. It was the "harmonic balancer" (crankshaft pulley) a local mechanic changed it for $60, the part cost me $120 (I work for a Ford dealership) $180 without employee discount. you can get one for much less at a junkyard if you can find one. Good luck, Sean

Posted on May 14, 2009

  • 62 Answers

SOURCE: replacing the harmonic balancer in ford bronco

First remove radiator fan shrould.This will give you access to the fan.Remove fan and fan belts.Remove bolt on harmonic balancer.You will need to rent a balancer remover and installer kit.Most big auto parts chains will rent these kits to you.Next remove four bolts holding pulley to balancer.Next attach balancer puller to balancer with long bolts from kit.Using a 1\2 drive breaker bar,remove balancer from engine.After removing balancer replace front seal.Lubricate hub on new balancer with engine oil.Then use installation tool from kit to install balancer.Never try to beat balancer on with hammer,engine damage could occur.Then work in reverse to replace remaining parts.Hope this will help you.

Posted on Aug 06, 2009

emissionwiz
  • 75822 Answers

SOURCE: Ford Explorer 2006 Overheating

then the head gaskets are blown

Posted on Aug 11, 2009

  • 834 Answers

SOURCE: how do i remove the

If there is no air-compressor and an impact gun to remove the harmonic balancer bolt, then there are two other ways to remove it. Either remove the inspection cover at the bell-housing and use a large flat head screwdriver to wedge between the flex-plate drive gear teeth and the engine block so that the engine is locked-up, and then remove the harmonic balancer bolt with a long breaker bar and a lot of muscle power, or for the more advanced mechanics and only they should attempt this, place a long breaker bar on the harmonic balancer bolt and then brace the breaker bar up against the frame of the vehicle so that when the engine turns over the breaker bar will stop on the vehicle frame, and keep in mind that the crankshaft will turn clockwise or to the right, and when you are looking for some place to brace the breaker bar be sure that nothing else will get in the way or it will be damaged. Be sure that the breaker bar is on the harmonic balancer bolt properly, and place the breaker bar about 1 to 2 inches from the vehicle frame so that when the engine turns the breaker bar will lock up against the vehicle frame, and while holding the breaker bar in place have someone turn the ignition key and give the starter a bump, and be very sure to keep your hand away from where the breaker bar is going to contact the vehicle frame, or your fingers will get smashed by the breaker bar when it turns into the frame so do not attempt this if you are unfamiliar with using hand tools, and the starter should break the harmonic balancer bolt loose easily, so be very sure that your hands are out of the way of getting hurt when the starter motor is used to break the harmonic balancer bolt loose.

Posted on Sep 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the nut out of the harmonic balancer


it should just unbolt ,but it is hard to get at it , and apply torque it is a right hand thread.

Feb 23, 2015 | 2006 Ford Explorer

1 Answer

How do I get the harmonic balancer off of my 2006 Ford Mustang


you will need a "Puller" to remove the "Balancer and there should be a bolt in the middle of the Balancer that holds it on to the crankshaft. You will also have to replace the seal that runs on the Balancer.
Before you do all that you will have to remove the fan shroud and whatever else needs to be removed to gain access to the Balancer and remove it.

Jul 23, 2014 | Cars & Trucks

1 Answer

I have a 2004 ford explorer with a 4.0 litier engine. u


Is this an Idler Pulley? Is it held under spring tension?

Oct 29, 2013 | 2004 Ford Explorer

1 Answer

Lincoln ls harmonic balancer part #


Although i would love to do so i cannot confirm that at this time. the part does not fit the 2006 lincoln ls but can be used on the ford crown victoria. the part ran at about a hundred and thirty dollars but there is also equipment required for the removal of the this part. this is a more prevalent part on chevrolet motors !

Apr 01, 2012 | Cars & Trucks

3 Answers

How do I take off the harmonic balancer on a 4.0 liter engine


You will have to take the belt off and then take the bolt out of the center that holds it onto the crankshaft. then You need a "harmonic balancer" puller, It has slots that bolt to the inner part of the balancer and you screw in the big center bolt. As you tighten the bolt it "pulls" the balancer. Here is a picture;

chuckster57_23.gif

Feb 08, 2011 | 1998 Ford Explorer

1 Answer

How do you replace crank sensor on a 2006 pontiac grand prix with the 3800 series 3 motor?


YOU HAVE TO REMOVE CRANKSHAFT HARMONIC BALANCER TO REPLACE CRANKSHAFT SENSOR.ITS LOCATED BEHIND IT.YOU NEED A HARMONIC BALANCER REMOVAL AND INSTALLER TOOLS.

Sep 13, 2010 | 2006 Pontiac Grand Prix

3 Answers

Severe vibration


Replace balancer. You don't notice them until you rev it up.

Aug 23, 2009 | 1996 Ford Explorer

1 Answer

Harmonic Balancer and fuel pump.


435 ONLY if it came from dealer. harmonic balancer can be a costly job. ask your mechanic to see the bill that he paid for the pump. just looking at interent i see pepboys has fuel pumps for 200

Dec 28, 2008 | 2004 Ford Explorer

1 Answer

I can,t find my explorer 96 timing marks


try looking near your harmonic balancer,
a video of how to replace your timing belt is here, http://www.wonderhowto.com/how-to/video/how-to-replace-a-worn-timing-belt-102454/
hope this helps

Nov 12, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
1996 Ford F150 Regular Cab Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...