Question about 2000 Jeep Grand Cherokee Laredo

Open Question

How to reprogram 2000 Jeep Grand Cherokee - 2000 Jeep Grand Cherokee Laredo

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

Ad
  • 1118 Answers

SOURCE: how do I change the

follow top radiator hose from radiator to engine wear hose ends, it will be clamped to whats called the gooseneck, thermostat is under that. you will have to drain coolant, not all, maybe 1 half gal. before you remove it. 2 bolts new gasget new thermostat, just remember spring on new thermostat goes in engine.

Posted on Feb 01, 2009

  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

Molson02536
  • 3854 Answers

SOURCE: how do you change the tps on a 2000 jeep grand 4.7

The exact placement of the throttle position sensor generally is located on the side of the throttle body below the air intake tube on top of the engine.

To replace simply remove the air intake duct (usually one plastic screw), locate the sensor, disconnect wire plug in, remove the two sensor mounting screws (torx screw variety, size not remembered) and the sensor will come off. When replacing be sure to line up the throttle shaft with the proper groove inside the sensor...it should just slip in there pretty easily with a little bit of wiggling. Reinstall doing the reverse of the above.

Take's about 5 - 10 min to replace from start to finish and remember to clean the throttle body before starting this job to ensure no dirt will enter the engine. Good luck, Merry Xmass

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does reprograming mean when it shows up on dash


the ACM in the control module has lost this program needs to go back to the dealership to be reprogrammed you said about a hundred To125 dollars

Jan 12, 2015 | 2000 Jeep Grand Cherokee

1 Answer

How to disalarm a 2000 jeep grand cherokee limited


may be you should make a diagnostic and you can do it in a garage or you can do it by yourself if you want to do it by yourself you need some tools and you can find some good ones here: xcardiag.com

Feb 26, 2013 | 2000 Jeep Grand Cherokee

1 Answer

My 2000 grand cherokee starts but then shuts down after 2 secs. door locks don't work right. new battery, cables are good. some of the dash lights don't work.


sounds like you have a problem with your chipped key try spare key if it works you will have to take it to dealer and have it reprogramed

Jan 25, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I'm trying to locate the thermostat on my 2000 jeep grand cherokee


  1. On 2000 Jeep Grand Cherokee 4.7L V8
  2. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  3. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

2000 Jeep Grand Cherokee 4.0l v6
Note:on the In-line 6 4.0L model the thermostat housing is mounted at the top of the engine block next to the water pump.

Nov 14, 2010 | 2000 Jeep Grand Cherokee

1 Answer

I have a 2000 Jeep Grand Cherokee. The remote power locks stopped working. The lights still flash and horn blows but the locks do not work. Any help ?


buttons are worn inside if you lived close i could probably repair it. you can go to salvage yard and get another one and program it your self using internet,or have chrysler reprogram it for you.

Oct 19, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2005 Grand Cherokee: the key worked up untill now 2005 jeep grand chero...


if the key has been dropped or kept near a high magnetic item (a tv screen)it will go out,use the spare until you can get all keys reprogrammed together

May 06, 2010 | 2005 Jeep Grand Cherokee

2 Answers

Lost jeep 2000 grand cherokee key and remote


go to the car dealer and tell them that you need to get a new key and remote for your car

Apr 09, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Laredo Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...