Question about Ford Ranger

Open Question

Abs fuse and dash light fuse 94 ford ranger - Ranger Ford Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 883 Answers

SOURCE: 2000 Ford Ranger

TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Posted on Jun 11, 2008

Ad
  • 20 Answers

SOURCE: 94 ford f350dash lights and tail lights not working

You may have a bad light switch or a bad wire at the light switch.
Only way to know is to remove the switch.

Posted on Feb 24, 2009

daves944
  • 1050 Answers

SOURCE: firing order on a 94 ford ranger 3.0

Sorry, that supposed to be under solutions.a79bdf6.jpg

Posted on Mar 26, 2009

co7196
  • 3433 Answers

SOURCE: ABS light on 2003 ford explorer stays on

It could be a wheel speed sensor. have your brakes inspected. good luck

Posted on May 30, 2009

mcgyver468
  • 710 Answers

SOURCE: How to remove fan clutch on 94 Ranger 4.0?

THERE IS A SPECIAL TOOL THAT CAN BE RENTED OR PURCHASED AT YOUR LOCAL AUTO PARTS STORE. IT CONSISTS OF A LARGE OPEN END WRENCH AND A LONG FORK-LIKE TOOL THAT GRABS THE NUTS ON THE FAN SO THAT THE WRENCH CAN LOOSEN THE LARGE NUT THAT HOLDS THE FAN CLUTCH TO THE FAN. I HOPE THIS HELPS. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING. P.S. BE SURE TO LOOK AT THE NEW CLUTCH TO FIND OUT WHICH DIRECTION THE THREADS GO. SOME OF THESE ARE LEFTY TIGHTY, SOME ARE LEFTY LOOSEY. GOOD LUCK

Posted on Aug 22, 2009

Testimonial: "Very Helpful "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Mazda B4000 abs light flashes 16 times, dash light does not work, and tail lights do not work. No blown fuses for the lights. Unhooked trailer wire harness.


93 ranger 2wd xl abs light blinking 16 times and rear brake light fuse blows when lights on and u hit the breaks but if the lights are off and u hit the brakes it fine i just installed today also the plug and play trailer harness but i didnt think that has anything to do with it.

i drive a 1994 ford ranger 2wd reg cab 4 cyl 2.3

Jan 03, 2017 | Mazda Cars & Trucks

1 Answer

My 4x4 button on my dash wont turn on and my 4x4 wont engage . I used it yesterday, usually lights up and 4x4 engages 94 mazda b4000 le 4x4 .


Ford Rangers and Mazda b-series vehicles are the same. I would be willing to bet it is a problem with your shift motor. There is a sensor on the motor that tells the "shift computer" where it is in regards to position. The sensor has a ceramic disk that is glued to a shaft. The glue dries out and the disk doesn't spin with the shaft, so the computer doesn't know the position. You can disassemble the shift motor and re-glue, or just replace the entire shift motor assembly. It's $85 - $100 for a remanufactured unit from Napa (or similar). I just did this for my '94 Ranger, tore it apart and fixed it.

Before doing any of that I would check the 4x4 fuse in the box under the hood. The other fuse to check is inside the cab. It is on the same circuit as the warning lights (if your dash warning lights work, that fuse is fine).

Here's a guide for troubleshooting other transfer case issues.

Transfer Case Troubleshooting The Ranger Station

Nov 18, 2016 | Mazda Cars & Trucks

1 Answer

Dash lights, parking lights, and brake lights quit working on my 1993 ranger. headlights still work. help!


ABS light is on because brake light circuit is down. Did you replace the park lamp fuse? Check trailer light connector if you have one.

Nov 29, 2012 | Cars & Trucks

2 Answers

Can't find wiper relay on 94 ranger


Wipers do not require a relay. If your wipers are not functioning and a fuse is blown, the washer will not work either. If the washer works, check the wiper switch or the wiper motor, but wiper motors are normally very reliable.

May 17, 2011 | 1994 Ford Ranger Supercab

1 Answer

Tail lights and dash lights wont work 2001 ford ranger


Check fuse NO.11(7.5amp) in the under dash fuse panel.

Jun 16, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

94 ford ranger blowing fuses when i turn on headlights


I would check the trailer light wiring to make sure it doesnt have any wires that are exposed or touching metal.Odds are that is what is causing the fuse to blow

Apr 23, 2009 | 2004 Ford Ranger

1 Answer

ABS light won't turn off.


It could be that changing the switch told the ABS there was a fault. Try removing the fuse for the ABS and waiting 5 minutes for it to reset. ---I had a small ABS issue with my Volvo and the ABS fuse had blown. Good luck-- and if this helped can you give a rating?

Mar 27, 2009 | 1999 Ford Ranger SuperCab

3 Answers

95 FORD RANGER NO INST. PANEL LIGHTS AND PARKING LAMPS


you might have blowed blulbs check that also there might be what is called a fuse link in the wiring

Mar 15, 2009 | 1995 Ford Ranger Supercab

2 Answers

1991 Ford Ranger w/ABS Rear brakes lockup


sounds like you need to replace the wheel cylinders also check brake shoes and adjust properly upon reassembly

Jan 30, 2009 | 1989 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...