Question about Cars & Trucks

Open Question

What is the cylinder head torque specifications for mtd snowflite 5/24

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: torque specifications cylinders head bolts

for 1.5/1.6L DOHC, 18 Ft-lbs + 70deg + 70deg + 50deg

for 1.8/2.0L DOHC, 18Ft-lbs +90deg + 90deg +90deg

Posted on Jun 24, 2009

Ad
  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 73 Answers

SOURCE: 3 vz-e engine cylinder head torque specifications

33 ft-lbf then 90 degrees then another 90 degrees

Posted on Sep 19, 2009

Testimonial: "this was not easy to find thanks"

drsinister69
  • 2317 Answers

SOURCE: What is the right Torque Specification of the

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 yaris 1.5 Ing. What's the torque pressure on heads


PDF]Complete Cylinder Head Torque Specifications for Domestic ...

olybrake.com/pdf/fel_pro_torque_specs_guide.pdf
When you consider what can go wrong when even "minor" gaskets fail, ... and engine block, tightening the head bolts compresses the gasket slightly, allowing ...Missing: ing

How To Torque Cylinder Head Bolts - EricTheCarGuy ...

? 25:08
https://www.youtube.com/watch?v=5WHBskK_F3o
Aug 29, 2010 - Uploaded by EricTheCarGuy
How To Torque Cylinder Head Bolts - EricTheCarGuy http://www.ericthecarguy.com/ Well ... What's the reason for changing the torque pattern?Missing: yaris

CTA Tools 9295 Toyota Head Bolt Wrenches -Dou



Dec 30, 2015 | Cars & Trucks

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

HEAD TORQUE AND SPECS FOR A 2001 HONDA ACCORD 2.3L


Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

10_29_2012_10_15_36_pm.gif

Oct 29, 2012 | 2001 Honda Accord

2 Answers

Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex


The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

The torque specifications are as follows:

> Step 1: All bolts: 22 Ft Lbs (30 Nm.)
> Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

May 20, 2012 | GMC Sierra 1500 Cars & Trucks

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

2 Answers

Head gasket torque specifications and sequense


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    1 Answer

    I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003


    Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
    Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
    Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
    Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
    Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
    NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

    Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

    Jan 24, 2010 | 2003 Chrysler Town & Country

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    38 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...