Question about Cars & Trucks

Open Question

Do you carry the InnoDesk Thermo-Cut Tape Gun and if not, do you know who does? Thank you.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

What is an easy way to repair small tear in leather car seat


some auto stores carry but most craft stores carry a leather repair kit comes with multi colored little containers and different grain patches that u iron if you have a grain designed seat cost under 15 bucks and if you have a weird color u can mix colors to match

Aug 02, 2015 | Seat Cars & Trucks

1 Answer

My heating seat stopped working in my 2000 yukon denali


You have a broken wire in the seat. The blue wire inside the seat cushion will break or burn in two. If you are handy with tools you can remove the seat, remove the screws from the control switches cut the hog nose ring clips, undo the velcro on the back of the seat bottom and carefully remove the bottom seat cover. You will find that the blue heating element blue wire in burned in two. Cut the bad part out, slide some heat shrink tape over one end. Slide it far enough so that you wont shrink it from the solder gun. Solder the two wires together and keep the joint minimal so that the shrink tape will slide over the solder joint. shrink the tape with a heat gun or hair dryer.Put everything back in reverse order. You will need to go to an older conventional auto parts store and buy a hog nose ring kit with the pliars to replace the upholstery. Go to an upholstery shop and they can tell you where to buy it . It should cost 3 or 4 dollars. this whole seat repair should not cost over $8.00. Also remember check the fuses first and also remember that the seatbelt has to be fastened for the seat heater to work.

Jan 08, 2013 | 2000 GMC Yukon Denali

1 Answer

Spark pllug and coil wireing diagram. SEMPER FI ANDY


Hello, What a Marine doing with a Mercedes-Benz? You Marines like those Marine Mules with 106 recoilless rifle on them. and shoe leather that reason why the call you Grunts. If you can't ride a mule then you will walk. SEMPER FI Marine.


Before I can help you Marine Andy, I'll need to know the year and model of this German Taxi Cab.

That right, they use Mercedes and BMW for taxi cabs in Europe.



Also, if it is gas or diesel? The Mercedes 4 cylinder, 5, or 8 cylinder? Does it have one coil or each spark plug has coil? US Army SSgt, I walk the jungles of Vietnam, Thailand, Laos, and the desert of Ethiopia. Andy I think you for your service in the finesse US Military organization, Many-Many Thank to you and your buddy's that might not have come home. and those that did. All the Way, but if its an Officer we say "Out of Away" GB you. stewbison



I ask a young female soldier what was that she was carrying, and she said to me, well Sir, it my gun!! I smiled, and said, young lady if I was younger I would really show you what a gun is really used for. So, this young private said, what do mean Sir. Well, thinking about it's time to give all these soldier's some military education. I grab here rifle and grab my gun; and said: This a rifle and it used for shooting your enemy, and grabbing my crouch and say; This is my gun, and it used for fun. Therefore, Ladies, remember the next time you call your rifle a gun, their might someone really lay a gun to ya.... he,he,he,hey...SEMPER FI....

Sep 08, 2011 | Mercedes-Benz 420-Series Cars & Trucks

2 Answers

The car keeps over heating.


first thing to check is your anti-freeze level ...if that is good put a thermo-gun to your thermastat housing and see if the themastat is opening at the proper temp ...may just be stuck closed cheap fix

May 17, 2011 | 1994 Lexus LS 400

1 Answer

My 1986 xj6 runs great when you first start it but when it warms up it starts to cut out and miss


thats my same problem, did you already found the answer? I change air flow meter, coolant sensor, fuel injectors, change hoses, i take out the charcoal cannister, everything, I dont know if the problem might be a temp sensor, or a thermo time switch, please if you find out let me know cause Im getting crazy. automotrizdeleste@hotmail.com

Aug 13, 2010 | 1986 Jaguar XJ6

1 Answer

Loud fan noise near radiator when idling


It may be the thermo fans that are on the car.They cut in and out especially if the air/con is on.The car will have a belt driven fan but the electric thermo fan,will cut in and out as it is needed creating a highspeed fan noise.Hope this is the problem and helps you.

Aug 24, 2009 | 2004 Nissan Sentra

1 Answer

Front drivers side window misalignment


Take the door panel off slowly because it's only held on with plastic clips. There is a plastic inner to the door, cut this carefully with a sharp knife, so you can repair with gaffer tape later. Lower the window, dont put your hands ANYWHERE near the movement at the moment. Now, slowly click the switch so the window goes up, dont press and hold, or it will go up all the way. (as you know) as the mecanised system goes up, it looks like a pair of scissors, watch where the window grabs, it will be plainly obvious, the window will start to judder. click the switch once moreto see where the scissor action is failing. Once you have found that, grease that area as much as possible. lower the window again, raise the window, if it sticks, lower it again and carry on until the grease works into the scissor action, don't try to actually take the window out, it's arder to get back in, start the engine (cos it does take a lot outof the battery) and just keep lowering and raising the window until the grease works in. Once that has been done, close the window up to the full height, tape the plastic back in place, because the door speaker could get damaged, and clip the door panel back in place. Job Done. Hope all goes well, let me know, regards, Dave

Aug 02, 2009 | 1994 Volvo 850

2 Answers

Rubber on the inside of car door door is ripped


if you do use glue use a hot glue gun but becarefull not too touch the rubber with the gun

Jul 22, 2009 | 2001 Chevrolet Suburban

3 Answers

How do I loosen the bolt on crank shaft?


Hi Manuel

The bolt comes off, in an anti clockwise direction.

I normally put a socket on an extension bar, with metal tube, to extend the length, on to the crank pulley bolt.

Secure under the vehicle with wooden block, and spin he starter, this will loosen it off no problem.

But this procedure must be carried out, before the cam belt timing is disturbed.

Airgun can be used to replace the bolt.

Good Luck !

A FixYa rating would be Nice......Thank you ! John.



Feb 16, 2009 | 1999 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...