Question about 1995 Dodge Ram

Open Question

How to remove a spindle front knuckle on a dodge ram pu

4WD

Posted by on

  • Jane Melton
    Jane Melton Jan 02, 2013

    how do you get off the bottom nut

×

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

Ad
  • 3 Answers

SOURCE: front hub bearing removal 2002 dodge ram 1500 4WD 4.7L V8

i just did a 2002 2500 4x4 with a dana straight axle and had no problem getting on the bolts with a 9/16 12 point socket on a 6 inch extension. If you do not use an extension the head of the ratchet will hit the yoke of the axle shaft.

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: Clicking noise in front end 2001 dodge ram 4x4

the ansew i found is replacing the seal around the joint and from both end removing it and cleaning it out i had rocks in mine from going threw water and mud ita a all day deal but a twenty doller fix axle shaft oil seal is all i had to replace

Posted on Apr 26, 2009

  • 1 Answer

SOURCE: 2002 dodge ram 4WD front hub bearing

Here is the easiest way . take a 14mm socket and extentsion and place it on the bolts and place againt your axle tube and start your truck and turn your wheel against it instead of pounding you will use your powersteering like a press to get your hub out its quicker and less strenous than pounding on the bolts ive done this many times i even made a extentsion for it i use a 14mm 1/2 drive shallow socket and a extension thats about 4 inches long i know im posting late on this one but if it helps anyone out then great

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE NAME OF THE PART THAT THE INNER cv jOINT IS INSERTED INTO ON A 2006 dODGE RAM 1500 WITH 4WD


The CV shaft mates with a SPLINE,The assembly passes through the STEERING KNUCKLE.Hope that helps

Oct 19, 2014 | 2006 Dodge Ram 1500

1 Answer

Do you have a video on how to remove front roter on a 95 dodge ram 2500 4 x 4


first remove center axle nut 1 11/16 then jack up & support truck remove tire then brake caliper then on the back side of knuckle remove the three bolts that hold wheel bearing onto spindle . then lightly tap free (not heavy force)

Jul 30, 2014 | Cars & Trucks

1 Answer

How can I remove a right front wheel hub seized in a steering knuckle


yeh they get stuck in there sometimes, beat the **** out of it till your fed up then remove knuckle and have it pressed out.

Mar 14, 2012 | 2000 Dodge Durango

1 Answer

Replace front passenger side u-joint on 4x4 drive axil


The wheels have to be removed, along with the brake calipers. There are four bolts that hold the unit hub bearing onto the front knuckles. The hubs have a very tight tolerance area that fits into the knuckle.
Sometimes the hub siezes into the knuckle and this is where the labor and parts can pile up. What makes this even more difficult is that the brake rotor can only be removed after the hub is knocked out of the knuckle, so it all has to come out as an assembley.

There is a nut in the middle of the hub. That nut is on the end of the axle stub, which passes through the hub bearing. If they make good time getting the hub and all out, they can still get stuck trying to get the stub shaft out of the hub. And it will have to come out to get the U joint out. Replacing the U joints should be straight forward.

Jul 11, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

How do I get the axles out of a Dodge Ram 1500 4WD?


Remove the hub/bearing assemblies and the axles will pull right out. 3 bolts (12 point bolts) hold each bearing to the knuckle, and the bearings may be frozen into the knuckles - this can be a problem and you may need the assistance of a pro if you can't get them out.

Jun 30, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

HOW DO I REMOVE ANS INSTALL WHEEL HUB 2002 DODGE 1500 PICKUP!WHAT


4x4 has 3 bolts in back of knuckle take them loose and tap on them to force the hub out of the knuckle

Jan 19, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Wheelbearing replacement


Hello
Welcome to FixYa
the front wheel bearing is a hub unit.
need to remove the tire,brake caliper, rotor, the 34mm nut in the axle, then there is 3 bolts that hold the hub to the spindle, those come off then the hub comes out,reverse to install.
RD

Jan 12, 2009 | 1998 Dodge Ram 1500 4WD

3 Answers

Remove front axle from differential on 2003 dodge ram


That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Jan 06, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

Front hub bearing removal 2002 dodge ram 1500 4WD 4.7L V8


i just did a 2002 2500 4x4 with a dana straight axle and had no problem getting on the bolts with a 9/16 12 point socket on a 6 inch extension. If you do not use an extension the head of the ratchet will hit the yoke of the axle shaft.

Dec 07, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...