Question about 1990 Volkswagen Golf

Open Question

Timing marks for 1600 vw golf to fit timing belt

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Timing Marks on VW Jetta GL 1995 2.0 Litres

timing belt marks

Posted on Apr 21, 2009

Ad
  • 8 Answers

SOURCE: Need help fitting a clutch on a VW GTI Golf

undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be removed.new clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

Posted on Jul 23, 2009

SOURCE: vw golf 1.4 16v after changeing timing belt car

The timing could be 180 degrees out you will have to do it all over again. Bring #1 cylinder upto TDC check the distributor rotor arm that it is pointing to #1 plug wire, It is important that the cams are on the intake stroke and not on the exhaust stroke. The crank is no big deal just make sure the marks are lined up.

Posted on Sep 10, 2009

  • 1757 Answers

SOURCE: need diagram of timing belt marks 4 golf gti mk3

Click on the following Link. It has all the Diagrams you will need.
Before clicking, let me know if this helped.

http://www.2carpros.com/car_repair_information/year/1996/make/volkswagen/model/gti/1996_volkswagen_gti_timing_belt_diagram_marks.htm

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I Have a VW Golf 1,3 Shuttle And Need A Cam Belt Timing Diagram


Have a look on the link below - particularly in the images. You may be able to identify which engine is yours:

vw 1 3 timing marks Google Search

Apr 20, 2016 | Cars & Trucks

1 Answer

Where are the timing belt marks on a 1987 vw golf 1.8


http://www.honestjohn.co.uk/forum/post/index.htm?t=72355 this link has some chaps from the UK talking about aliging their VW golf timing marks with some good detail hope this helps.

Jun 11, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

NEED TIMING MARK DIAGRAM FOR 1989 GOLF 1.6 DIESEL TO REPLACE TIMING BELT


The timing belt marks diagram for 1989 VW Golf 1.6 Diesel

tdisline_534.jpg
tdisline_535.jpg

May 15, 2011 | 1989 Volkswagen Golf

1 Answer

How do I align the timing marks on my 1997 vw polo 14i when replacing th timing belt


bring engine to TDC no1 then use some white paint to mark gears and backplate ,then it doesnt matter where the timing marks are

Apr 19, 2011 | 1997 Volkswagen Golf

1 Answer

I replaced my 2006 vw citi golf timing belt,now the car doesn't have any power and uses alot more fuel,could you please help me fix this problem.it is a 1.4 carburator engine


you need to confirm back your timing marking of the engine. make sure all the mark is on the dot. even miss 1 notch it run bad.

Nov 21, 2010 | 1999 Volkswagen Golf

1 Answer

How do i replace the timming belt on a 1996 vw glof 2.0


if you havn' t done it before best to get an experienced technician to do it. [critical part, can cause major damage if incorrectly fitted]. before removing belt line up timing mark on crankshaft pulley with arrow on timing belt cover. remove inspection plug on top of gearbox bell housing. v cut away on fly wheel should be lined up with notch on g/box housing. timing mark on inside of camshaft pulley must line up with top of cylinder head surface at front of head. if distributor fitted, remove cap . rotor should be pointing to mark on distributor housing. remove old belt, fit new keeping timing marks in same positions. tension cambelt. should be able to turn belt 90 degrees side ways between cam pulley and intermediate pulley if tension is correct. reset ignition timing on completion.

May 20, 2010 | 1996 Volkswagen Golf

1 Answer

What are the marks for the camshaft on a 2002 VW


There is a cutout on the inner part of the camwheel. It has a demarkation shaped like the tip of an arrow. This should line up to the 3:00 point on the edge of the head. you can tell for sure because at this position you should easily be able to move the camshaft sprocket about 3/4 inch in both directions easily from the pinpoint.

Sep 08, 2009 | 2002 Volkswagen Golf

1 Answer

1999 vw golf timing belt


if you dont know or are unsure change it for your own piece of mind

Jan 14, 2009 | 1999 Volkswagen Passat

Not finding what you are looking for?
1990 Volkswagen Golf Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...