Question about Cars & Trucks

Open Question

How to disable alarm system 4 a Ford Escape 05

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: lost the remote for 2004 Ford Escape, need to disable the alarm

try disconnecting the battery cables from the battery for up to a half hour and then reconnect them. im not sure if this will work for you but i have seen it work on some other vehicles, it couldnt hurt to try... hope this does it for ya

Posted on Mar 24, 2009

CMV9
  • 594 Answers

SOURCE: Brake drum 2005 Escape

here is a diagram on how to remove your brake drum. please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the tire and wheel assembly.

    CAUTION Use of a brake drum puller or a torch is not recommended. Brake drum distortion can result.

    NOTE If the brake drum is rusted to the axle shaft pilot diameter, tap the center of the brake drum between the wheel studs.
  3. Remove the brake drum.
  4. If equipped, remove the brake drum retaining clips.
  5. If the brake drums will not come off, follow these steps.
  6. Move the brake shoe adjusting lever off the brake adjuster screw.
  7. Loosen the brake shoe adjuster screw nut by adjusting the nut upward.
  8. Using the special tool, 134-R0191, measure the brake drum inside diameter.
  9. Install a new brake drum if the maximum inside diameter exceeds the specification shown on the outside of the brake drum.
    67197-esca-g51.gif Drum brake exploded view
To install:

WARNING Whenever a wheel is installed, always remove any corrosion, dirt or foreign material present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Failure to follow these instructions may result in personal injury.

  1. Clean the wheel hub mounting surface and wheel pilot.
  2. Install the tire and wheel assembly.

Posted on Apr 16, 2009

  • 356 Answers

SOURCE: pdf download of an '05 or '06 ford escape

http://www.ebookspdf.com/automotives/3197/ford-escape-2005-owners-manual/

Free one.

Posted on Oct 03, 2009

  • 54 Answers

SOURCE: NEED TO DISABLE ALARM ON 2002 FORD ESCAPE

if your battery died or you replaced battery, disconnect the postive terminal from battery. insert key into igniation to on position (not start) then reconnect the battery postive terminal.

Posted on Sep 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disable the seat belt alarm on the 2011 ford escape


You have to find the alarm, unplug it or cut the wire to it.

Jan 31, 2017 | 2011 Ford Escape

1 Answer

How do I disconnect factory car alarm?


Mostly you can't as the alarm and immobiliser is integrated into the vehicle/engine management system.

It might be possible to disable it by getting at the software if you have the skill and a laptop with the right programmes but other than that disconnecting the sounder is all that is possible.
Some of the earlier Ford alarms were operated by a separate module that could be disconnected. Unfortunately these were hidden behind the dashboard and impossible to reach without first removing the dashboard.

Dec 03, 2015 | 2005 Ford Escape

1 Answer

How do I de-activate a2005 ford escape factory alarm?


Bring the car to dealer,
ask... where is the alarm?
Say...where is the fuse for that alarm?
permit the attendant at hand to take out the fuse.

Mar 10, 2015 | 2005 Ford Escape

1 Answer

How do i disconnect the door ajar alrm on a


Hook up the Ford VCM IDS system, find out Customize setting functions, it can be easily disabled as well as other options,like disable DRLs, TPMS etc

Best Quality VCM II For Ford Multi Language Diagnostic Tool

Oct 10, 2014 | 2005 Ford Escape

3 Answers

My 2008 Ford Escape has power. Lights work, wipers, everything works that has power but when I try to turn the key to start it nothing happens. I mean I don't even hear a clicking noise


Check the relays and fuses in the Power Distribution box under the hood. If all are good check the Alarm circuit ignition kill switch. If you didn't get the Alarm built into the vehicle but had it installed after you bought it remove the fuse from the Alarm power line to disable the kill switch. I did have this problem once and it turned out to be the battery on mine, a 2005 with Alarm built in. Unless you have the Hybrid version you could get in 2008 the vehicles are basically the same.

Dec 31, 2010 | 2008 Ford Escape Hybrid

1 Answer

NEED TO DISABLE ALARM ON 2002 FORD ESCAPE


if your battery died or you replaced battery, disconnect the postive terminal from battery. insert key into igniation to on position (not start) then reconnect the battery postive terminal.

Sep 18, 2010 | 2002 Ford Escape

1 Answer

Lost the remote for 2004 Ford Escape, need to disable the alarm


try disconnecting the battery cables from the battery for up to a half hour and then reconnect them. im not sure if this will work for you but i have seen it work on some other vehicles, it couldnt hurt to try... hope this does it for ya

Mar 24, 2009 | 2004 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...