Question about 2006 Toyota Tundra

Open Question

How do you remove 140 amp fuse from a 2008 toyota 4runner

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 1992 toyota 4runner

what is the black lose wire hanging lose in back i think the drivers side in the back compartments

Posted on Jan 19, 2009

  • 48 Answers

SOURCE: Removing the 100 amp fuse link in a 1994 toyota corolla

the fuse link is bolted in from the two side in the fusebox.you have to un bolt the whole fusebox so you can raise it and if you look at the sides there are two side panels that can be moved down so you can get a socket or spanner on the two bolts apprx 10mm. undo them and raise the fuse out and put the new one in and tighten up the bolts again. hope this helps.

Posted on Apr 25, 2009

mkv0525
  • 358 Answers

SOURCE: 140 amp fuse blown request replacement instructions

you have to remove or access the bottom half of under hood fuse panel to remove bolts on teh bottom of that fuse.

Posted on May 20, 2009

  • 11 Answers

SOURCE: Remote Start on 2008 Toyota 4Runner will not start truck

Is it a Toyota remote start, or an aftermarket remote start? If it is a Toyota remote start, make sure the hood and doors are all closed. press lock twice, then press lock a 3rd time and hold it for 3 or 4 seconds. It then should beep once, and a few seconds later start up. OR the lights will flass once, twice, or etc. Usually this means there's something wrong and the number of flashes is a diagnostic code of sorts. If this is the case, take it in to your dealer for further assistance. This part should be covered under the 3/36000 warranty.

If it is an aftermarket system, it will probably be a similar situation. It may be a misadjusted hood pinswitch, or even some blatent mistake the installer made installing it.

Posted on May 31, 2009

  • 3 Answers

SOURCE: Removing and replacing stock radio on Toyota 4runner 03

crutchfield.com is easiest way.also will allow you to leave the factory harness intact.

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box diagram toyota 4runner 2008


On this website (link below) you find fuse box diagram and description for Toyota 4Runner (2005 - 2009)


Toyota 4Runner Fourth Generation N210 2005 2009 fuse box diagram Auto...

Jun 12, 2013 | Cars & Trucks

1 Answer

Can I dsiable abs brakes 2002 4runner


You can remove the abs pump fuse & see what
happens

The question is why?

You have conventional brakes until a wheel slips

I would command the hcu unit open & then remove the fuse

When you go to inspection, you fail, as the ecu/pcm/ecm, etc
won't be ready,it will be looking to run a test on abs every time
you start the engine or turn key on

Feb 14, 2013 | 2002 Toyota 4Runner

1 Answer

How do you remove the charging system fuse in a 1997 Toyota 4Runner


Perfect Answer

I hope a lot of people read that

It is not a good idea to use any of todays
vehicles to jump each other

Use a separate battery pack designed for that
or a battery charger on boost

You can also ruin the electronics just being helpful
to someone

Oct 21, 2012 | 1997 Toyota 4Runner

1 Answer

The cargo light in my 2008 Toyota 4-Runner has apparently gone out. How can I repair it?


If it's not the bulb (try changing that) then it might be a fuse

Apr 16, 2012 | 2008 Toyota 4Runner

1 Answer

1998 toyota 4runner reset check engine light


Hi. You can reset the check engine light by removing the blue 15 amp EFI fuse (fuse box under the hood). If you do this, and the check engine light is illuminated again, you will need to address the cause for the light to be on; you have a 'hard fault'; and a part may need replaced.

Nov 24, 2009 | 1998 Toyota 4Runner

1 Answer

140 amp fuse blown request replacement instructions


you have to remove or access the bottom half of under hood fuse panel to remove bolts on teh bottom of that fuse.

May 17, 2009 | 2004 Toyota Tundra

Not finding what you are looking for?
2006 Toyota Tundra Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...