Question about Cars & Trucks

Open Question

Where is oil pressure sensor on 2001 chevy monte carlo ss

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2001 monte carlo

do you have spark if you have no spark the crank sensor is bad.do you have fuel presure now. if not check the fuses. nead more info

Posted on Nov 23, 2008

SOURCE: monte carlo 2001 ss 3.8 V6

is the battery good if it is shorted out it will do this or if the charging system is not working

Posted on Nov 23, 2008

ginko
  • 19396 Answers

SOURCE: 2002 monte carlo ss

The fuel filter is located in the pressure line that runs from the fuel tank to the engine, near to the fuel tank.
Keep the engine off for few hours before replacing the filter, to get rid of some pressure in the lines.

Posted on Feb 27, 2009

c17hydro
  • 2984 Answers

SOURCE: crankshaft sensor on a Monte Carlo 2001 SS 3.8

3.8L Engine

  1. Turn OFF the ignition.
  2. Remove the serpentine belts from the crankshaft pulley.
  3. Raise the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the right inner fender access cover.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  8. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  9. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  10. Disconnect the sensor electrical connector.
  11. Remove the attaching bolts from the crankshaft position sensor.
  12. Remove the crankshaft position sensor from the block face.
To install:
  1. Position the crankshaft position (CKP) sensor to the block.
  2. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  3. Reinstall the crankshaft position sensor shield.
  4. Connect the CKP sensor electrical connector.
  5. Position the crankshaft harmonic balancer on the crankshaft.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  8. Install the right inner fender access cover.
  9. Install the right front wheel and tire assembly.
  10. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  11. Lower the vehicle.
  12. Reinstall the serpentine belts.

It looks like this:

fd368a5.jpg

Posted on Jan 10, 2010

jturcotte
  • 7704 Answers

SOURCE: how do i reset the

you need a scanner to clear the codes. make sure you have them written down first. Many parts stores offer free scans (autozone, Advance, etc.)

Posted on Sep 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace oil pump on 01 monte carlo ss


If the oil pan will clear the steering components without jacking up the engine then drop the pan and unbolt the oil pump. You'll need to get a new pan gasket for the oil pan too.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Where is the oil pressure switch located on a 202 monte carlo ss 3800


It is just above the oil filter. it is easy to see if you pull off the right front tire

Oct 31, 2012 | Cars & Trucks

1 Answer

Oil gauge on 02 monte carlo ss


Sounds like the oil pressure sending unit is bad.

Oct 19, 2012 | Cars & Trucks

2 Answers

I have a 2001 monte carlo ss keeps showing low oil pressure and they guage is going back and forth I have the right amount of oil in the engine


Could be a bad sending unit (sensor) casing the problem, or maybe something else:
You say that the "gauge is gong back and forth" when is this happening? At idle, then I would suspect the sensor. But other items might be the oil pump pressure regulator or a cracked pick-up tube, not likely, but possible.
Now if the gauge pressure is fluctuating while driving, there could be a host of problems such as: oil pump or main bearings wear or some internal leak.
The best test at this stage would be to connect a manual oil pressure gauge to the engine to see what exact oil pressure is reading.
Don't drive the car until you get this fixed. You could turn a small problem into a big one if the engine truly is not getting oil. A cheap repair could go to 3-4 grand if you fry the bearings in the engine.
Comment back with your mileage and further description of the problem if you want more help.
J (Working on Small Blocks since 1967)
(2.21.2011 00:42 PST)

Feb 21, 2011 | 2001 Chevrolet Monte Carlo

1 Answer

How do i reset the check engine light on my 2001 chevy monte carlo ss


you need a scanner to clear the codes. make sure you have them written down first. Many parts stores offer free scans (autozone, Advance, etc.)

Sep 23, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

Where is low tire sensor located?


the sensors are on each tire [its part of the valve stem] if warning light is on -one of tires need air also check pressure in the spare tire

Jun 08, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

Is it normaol for the oil pressure gague to go up when excelerating in a monte carlo ss 2001


yes it is. this is typical of most cars - the oil pump is gear driven, as your RPMs go up so does the oil pressure.

May 14, 2010 | 2004 Chevrolet Monte Carlo

1 Answer

My rpm is going crazy


Either the gauge is defective, the sensor at the distributor, or the computer module.

Could be a loose wire any where in the chain between the sensor and the gauge.

Mar 13, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

Its a 2001 monte carlo ss, the oil presure gage its show under just on 40 or less, it was god tha day before


Replace the oil filter, check the oil pan gaskets and/or take it immediately to a mechanic for pressure testing.

Oct 10, 2009 | 2001 Chevrolet Monte Carlo

1 Answer

2001 monte carlo


do you have spark if you have no spark the crank sensor is bad.do you have fuel presure now. if not check the fuses. nead more info

Nov 23, 2008 | 2001 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...