Question about 1994 Chevrolet Suburban

1 Answer

Hazzard lights not flashing, stay on

Replacement instructions

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

If the hazard lights do not blink and stay on either you have a bad bulb on each side of the vehicle or your flasher for your hazard lights is bad

Posted on Mar 03, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Turn signals stay flashing rely fast and the front ones dont turn on


When this happened to me, it ment the bulb was burned out,

Apr 09, 2014 | 2000 Mazda Protege

1 Answer

Turn signal wont flash, hazzard lights and turn signal just stay on, left side started blinking fast, then went back to normal, now they just stay on.


it may be the flasher unit is faulty & needs to be replaced, you should find it under the dash on the drivers side it could be a square or round unit with a connector plug on it, when you remove the connector plug the unit has three pins on it........hope this helps.......cheers.

Sep 23, 2011 | 2003 Ford Expedition

2 Answers

My 2008 Chevy Cobalt coupe has a passenger side turn signal that flashes fast on the instrument panel. However, no turn bulb is burnt out in either the front or rear. The rear passenger turn blub just...


It is as simple as your hazzard switch needs to be replaced yes your hazzard switch as now turn signals are built threw the hazzard switch my PT Cruiser had same problem as my s10 replaced hazzard switch fixed the problem

Aug 18, 2011 | 2008 Chevrolet Cobalt

3 Answers

My 2003 chevy impala turn signals won't blink. the lights come on but won't blink. I have checked the fuse. it looked fine.


Hi,

Your problem is your blinker or flasher, it is located under dash, behind the instrument panel right above the steering column. Cost is no more than $10.

If helpful, click below, GOOD LUCK

Apr 15, 2010 | 2003 Chevrolet Impala

1 Answer

I HAVE A 2002 JEEP WRANGLER SPORT. THE HAZZARD LIGHTS DONT WORK


I think there are 2 fuses for those switches. Fuse #11 & #39

Hope that works for you

Feb 22, 2010 | 2002 Jeep Wrangler

2 Answers

Turn signals come on but dont blink


its in the fuse box, round with 2 spade pins on older models, on newer ones they used morep ins...but same logic.

cycle and release your HAZZARD switch a few tymes. Hazzard switch has an over-ride for the turn signals, and sticky switches will sometymes cause a NO FLASH problem that a cycle of the switch can correct. If lights still dont flash, flasher unit has probably failed/

Sep 19, 2009 | Ford E-250 Cars & Trucks

2 Answers

Right turn signal is slow and left just stays on 1977 ford F100


wouldn`t hurt to have a look at the flasher unit, hazzard light are adifferent unit .you may even be able to see where it hasbeen getting hot------------ adios-ben

Aug 03, 2009 | 1981 Ford F 150

1 Answer

Turn sgnals, hazzard flasher and brake lights dont work


Sounds like either a fuse or bad flasher. Do the the turnsignal lights  light up and stay on?

Dec 19, 2008 | 1995 Mercury Sable

1 Answer

Hardbody 2002


get into the truck and close and lock the door. place the key in and out of the ignition cylinder about six times(not too fast or slow) until you see the hazzard lights flash twice. then turn the key to the acc. position and then press the lock button on the remote(if lock doesn't work you can push another button on the remote). if the hazzard lights flash it is now programmed. then turn the key to off and pull it out and then unlock the door and open and close it. now test the remote.

Jul 21, 2008 | 1990 Nissan Hardbody King Cab

Not finding what you are looking for?
1994 Chevrolet Suburban Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...