Question about 1991 GMC Sierra

2 Answers

How do I remove the pully from the ac pump

The 9/16 nut in the middle of the pully spins when I try to loosen it. How do I remove the pully from the unit?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go to autozone and tell them year make and model and they have loaner tools that will hold the ac clutch and so you can take the nut off and a tool that pulls and and installs clutch

Posted on Jan 02, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try putting a 9/16 ratchet on it while u loosen it

Posted on Jan 02, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 57 Answers

SOURCE: trying to replace water pump

you need to use a long flat head screw driver and place it between two of the other studs and hold it while you loosen your nuts. do not remove them untill they have all been cracked loose. be careful you can get hurt.

Posted on Jan 08, 2011

cyberfast
  • 155 Answers

SOURCE: loosening the nut between the fan and pully; to

a strap wrench should do the trick. there not that expensive.

Posted on Jan 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace water pump on a 2008 TOyota Yaris


Can replace without removing alternator or dropping engine.
loosen alternator..will need to move back and forth..remove belt
remove punp pulley using 10mm wrench..use combo open and ring..short and long wrenches....loosen and remove bolt on ac lone support strap..slide forward then up...us thick drill bit to thread through..pulley wheel hole to jam the pulley wheel...then loosen eack of the 3 bolts on the pully wheel..remove...you now have access to 3 retaining bolts and 2 retaining nuts on water pump..loosen....they are hard to get to but they can be loosenned from the top...open drain plug on radiator...open radiator cap and reservoir cap to drain.....with all bolts and nuts removed pull off pump,,,protect the mating surface and move forward and left and down and forward..it will come out...gasket and seal the new one and replace....install and tighten bolts cross wise,,evenly..put on pulley wheel hand tighten 3 10 mil bolts..replace belt..tension to hold pulley then further tighten bolts...refill radiator and reservoir..massage hoses to remove air..close up..run engine.few seconds..undo fill cap refill..repeat till all ait gone..inspect pump for leaks..done

Mar 09, 2013 | Cars & Trucks

1 Answer

I think my alternator belt is loose and im and trying to figure out how to tighten it.


there should be a pully in front of the axle next to the ac compressor that has a 14mm head/ nut lossen this 3 full turns the look at the top of this pully and you will see a 14mm nut that is used to tighten and loosen the belt. lefty loosey righty tighty.

Mar 19, 2010 | 2000 Nissan Maxima

1 Answer

How do i replace an idler pulley on a 02 xg350l


the 02 and the 05 are identical. There are TWO idler pullys ... one for the power steering, and the other for the AC compressor & alternator -- WHICH ONE? In any event, you'lll need to remove the right front wheel and the splash guard (10mm bolts) to access either of the pullys. Use 14mm wrench (or ratchet & socket) to loosen the appropriate pully (Pwr Steering has 14mm nut & two 14mm bolts), The other pully has one 14mm nut & one 14mm bolt.
Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Oct 14, 2009 | Hyundai Motor 2005 XG350

1 Answer

Need to replace just the belt for the ac on a 2000 doge caravan


there should by a small pully (called a tentioner) under the alternator pully, get a wrench that fits the nut in the middle and turn it counter clockwise this will loosen the belt to get it around the other pully. Ps. this is easier with two people, one to release tention and one to put the belt on.

May 15, 2009 | 2000 Dodge Caravan

3 Answers

1996 Chevrolet Cavalier, 2.2 Water Pump.Can't remove pully.


great problem this ,either put a big screwdriver through a hole and jam it up ,if no hole or offrice then use a big pair of super snap on water pump pliers

Apr 05, 2009 | 1996 Chevrolet Cavalier

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

1 Answer

Cooling Problem With My 97 S10 Blazer


Leave belt on, the fan clutch will loosen in the same direction that the fan turns while engine is running.There is a special wrench for these but, as a help to loosen it, with a heavy hammer and long chisel, place chisel blade near top of nut flat and strike firmly till it loosens in the direction the fan turns. This method is really not recommended as it is a shock load the water pump is not made for.Use care not to hit strait into shaft center. Before replacing fan blade, what caused fan to hit shroud?? Fix that so it don't happen again!Good luck! Freezing and thawing in Michigan!

Feb 08, 2009 | 1997 Chevrolet Blazer

2 Answers

How to replace a fanclutch on 2004 yukon denali.


you need to get a slip ring wrenchto hold it you can get one at sears

Dec 07, 2008 | 2004 GMC Sierra Denali

2 Answers

1990 cadillac deville need help water pump removal???


Water pump is located on the side with all the belts. Find the water pump pully and LOOSEN the bolts that keep the pully on the shaft of the water pump. Once they are LOOSEN remove the belt. Then you can remove the pully bolts the rest of the way. Pully MIGHT be stuck on there, a couple of taps should loosen it enough to where you can pop it off by hand. Now if I recall this vechile correctly, there MIGHT be another pully that will hinder you. It's just easier to take it off right away. It's right above the water pump. I BELIVE it's an idler pully. Dosn't do anything but to help keep the belt on it's correct path. There should be one bolt in the middle of this pully, undo the bolt and pully will pop off. Make sure you REMEMBER how it was on. So that you put it back on the right way. Then, there are 2 or 3 different sized bolts that keep the water pump on. Remove the bolts, one at a time, and make sure you REMEMBER where they went. If you remember now, it will save time guessing later. Ok, once you are sure that ALL the bolts are removed, you can try to pop off the pump. If it dosn't come by hand, use a screw driver to pry a corner up and then do the rest by hand. Once it's off, it's time to clean the motor side of the pump. See, on these cars it's not a complete pump like it use to be, it's a half pump. Meaning, when you look at one side you can see the fins that move the water. Anyways, when you are at the parts store, pick up some emery cloth. It's sort of like sand paper. Well, once the pump is off, use a razor blade and scrape off the silcone that's on the block. Then use the emery cloth to make is nice and clean getting all of it off. Once that's complete, put the new gasket on the pump and reinstall. Put all the bolts in BEFORE tighting them down. And when you do tighten them, do it by hand! Using an air tool will break the bolt or strip the threads in the alunimium block and then it has to go to a mechanic. Once all the bolts are tight fill up the reservor to check for leaks. Also go back over the bolts one more time and make sure all are tight. Doing this now, will save you headace later. Then put the rest of the things back on in the order you took them off. That's it exepct for bleeding the cooling system. I assume you know how to do this, if not, let me know.

Oct 19, 2008 | 1991 Cadillac DeVille

1 Answer

2000 Blazer 2D 4WD ZR2


The big nut spins counter clock wise. you have to put your pulley bolts back on and make sure they are tight. leave belt on so that you have more resistance to pull against when tring to loosen the nut put a bar inbetween the pulley bolts so it won't slip off and then loosen that big nut looking thing and you should have it from there. to the same thing in reverse order to install it

Jun 09, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...