Question about 2004 Chevrolet Aveo

Open Question

2004 Chevy Aveo - Do Fel-Pro orings for valve cover gasket go on top of bolt or on the block?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 61 Answers

SOURCE: how to replace valve cover gasket 1998 chevy malibu

The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced. 

Posted on May 06, 2009

tntjasmine
  • 24 Answers

SOURCE: Rear speakers for Chevy Aveo

you can access them from under the package tray inside your trunk compartment

Posted on Aug 26, 2009

  • 20 Answers

SOURCE: 2004 chevy aveo cylinder head bolt torque how many

Step 1: 18 lb.-ft.
Step 2: additional 60 degrees.
Step 3: additional 60 degrees.
Step 4: additional 60 degrees.
Step 5: additional 10 degrees.

Each step involves starting at the center two bolts of the head and alternately tightening in a criss-cross pattern, ending with the bolts on the outer edge of the head.

Posted on Sep 14, 2009

  • 118 Answers

SOURCE: how do you install a block heater on a chevy aveo 2006?

A block heater is installed in one of the freeze plug ports in your block. Drain your cooling system. Then drill a small hole i the center of the freeze plug and screw a self tapping screw into the hole. You can the use a claw hammer or something similar to pull the freeze plug. Then you just install the block heater in the freeze plug's place. Refill your cooling system and let it get up to full temperature checking carefully for leaks. Please rate my answer.

Posted on Dec 09, 2009

joshnaz
  • 186 Answers

SOURCE: how to change valve cover gasket 2005 aveo

take off the cover screws and cover. take off the valve cover bolts and remove the valve cover.

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is head bolt and torque sequence for 2000 Toyota tundra 4.7litre head bolts bought head gasket set for Toyota tundra 2000 4.7l from fel pro but can


Your shop manual should contain this info. Are you really doing this job without one? Bet a google search will find this info too.

Dec 02, 2014 | 2000 Toyota Tundra

1 Answer

We took off the breather cover on a 2004 chevy trailblazer and there was water in it


Sounds like you may have a bad valve cover gasket. same thing was happening on my wife's Chevy Aveo. Valve cover gasket was worn and when I replaced it and cleaned plug wells, issue was resolved.As for the breather, I really wouldn't know why there's water in there.Only thing I would suggest there is to check your antifreeze level. Is it water from the antifreeze?

Mar 24, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

2008 chevy aveo cover gasket


Replace the one fastener. Typically you don't have a torque sequence on a valve cover.

Keep an eye on the oil leaks. Problems like this one are why we mechanics don't make enough money. Everyone wants to fix it themselves and we go hungry because it looks easier that it really is. (Not being rude, just stating facts)
I hope you fixed your issue, and don't have any further problems. I would recommend taking it to a pro if you continue having issues. Something seemingly small like this can snowball quick.

Take it from a pro who has been there, done that, have too many teeshirts. :-)

Scott

Jan 22, 2013 | 2008 Chevrolet Aveo 1.6

1 Answer

I have a 95 dodge ram 3500. It has an Oil leak on the drivers side top of engine between the block and and the diesel fuel system. I have replaced 2 lines by the power steering pump, But that wasnt the...


The oil pump is located inside the engine. Down in the oil pan. It sounds like you need to replace your valve cover gasket. I would make sure to buy Fel Pro. They are the best gaskets in my opinion.

I hope this helps you! If so please click YES! Thanks!

Sep 01, 2010 | 1995 Dodge Ram 3500

1 Answer

We change the spark plug of my aveo 2004, and we found out that there is a oil leak on the third cylinder, what may cause the problem?


The valve cover has rubber o-ring seals that fit into the valve cover and seal oil out of the spark plug wells. Over time, they get hard and shrink, allowing oil to enter the plug wells from the top of the engine. You need to remove the valve cover and replace the valve cover gasket and o-ring seals. The seals should come with the valve cover gasket set.

Hope this helps,
Dave

Jul 03, 2010 | 2004 Chevrolet Aveo

2 Answers

Roughly how much would it to fix my 1999 chevy sub. V8 2wd. if water got in the engine? It has not over heated. And the water went bad also.


not much. buy some lucas oil engine flush fo the oil system,and run it thru. flush your cooling systemas well. this is all contingent that you fixed the problem that caused this in the first place. if you have...then around 50 bucks.

May 01, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Hi, I have a 2006 chevy aveo and I was recently told that I needed to replace the valve cover gasket because it's leaking oil. How do I replace a valve cover gasket on a 2006 chevy aveo? Much...


Its easy. I did mine about a month ago. You need to take off all the bolts on the top part of the motor. there are some tubes on the left side of the motor by pushing them out of the way... you take the old one off and replace it with the new one making sure its aligned and the you put it back on.. the bolts need to be hand tightened kinda as tight as you would do your tires.

Mar 24, 2010 | 2006 Chevrolet Aveo

2 Answers

After replacing valve cover gasket with dry fel-pro gasket,


Your new gasket has tabs that make it easy to set in place; the tabs hold the position properly on the cylinder head. The gasket also has the rubber coating to establish a tight seal between the cylinder head and the the valve cover, even if there is slight damage or warping. Proper torque for the valve cover bolts is between 50-100 in-lbs., which is about 8 ft-lbs for a maximum.

If you have the gasket properly set, and proper torque on the valve cover bolts, you should not leak.

If you still experience a leak after double checking the gasket and the bolt torque, I would replace the valve cover itself. You will find several at most any salvage yard, and probablly will cost you $10.00 or less for a used valve cover.

I hope this helps you, and I wish you luck on your repair.

Apr 23, 2009 | 1993 Ford Escort 4 Door

2 Answers

How to install a intake on a big block chevy corvette


That depends on type of gasket being used. Some fel-pro gaskets have sealant built into the gaskets, I have used some sealant to help hold gaskets in place around bolt holes during installation but that's not always necessary...and yes there is a torque sequence for intake manifolds...example given in link.

The balancer should be torqued also...85 - 90 Ft-lbs if I remember correctly. The balancer should be all the way back when completely torgued, if not you may need to check for clearance problems.

Apr 05, 2009 | 1965 Chevrolet Corvette

4 Answers

Torque specs for the cylinder head


2004 ENGINE
Engine Mechanical - 1.6L (L91) - Aveo
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fastener Tightening Specifications
Application
Specification
Metric English
A/C Compressor Mounting Bolts 27 N.m 20 lb ft
A/C Compressor Mounting Bracket Bolts 50 N.m 37 lb ft
Air Filter Housing Bolts 12 N.m 106 lb in
Alternator Adjusting Bolt 20 N.m 15 lb ft
Alternator Adjusting Bracket Retaining Bolt 20 N.m 15 lb ft
Auxiliary Catalytic Converter-to-Exhaust Manifold
Nuts and Bracket Bolts
40 N.m 30 lb ft
Camshaft Cap Bolts 16 N.m 12 lb ft
Camshaft Gear Bolt 67.5 N.m 49 lb ft
Camshaft Pressure Plate Bolts 10 N.m 89 lb in
Connecting Rod Bearing Cap Bolts 25 N.m+30°+15° 18 lb ft+30°+15°
Coolant Pump Retaining Bolts 10 N.m 89 lb in
Coolant Temperature Sensor 20 N.m 15 lb ft
Crankshaft Bearing Cap Bolts 50 N.m+45°+15° 37 lb ft+45°+15°
Crankshaft Position Sensor Retaining Bolt 10 N.m 89 lb in
Crankshaft Pulley Bolt 95 N.m+30°+15° 70 lb ft+30°+15°
Cylinder Head Bolts - Camshaft Support Housing
and Cylinder Head Mounting Bolts
25 N.m+60°+60°
+60°+15°
18 lb ft+60°+60°
+60°+10°
Electronic Ignition System Ignition Coil Mounting
Bolts
10 N.m 89 lb in
Electronic Ignition System Ignition Coil Mounting
Plate Bolts 10 N.m 89 lb in
Engine Mount Bracket Retaining Bolt 65 N.m 48 lb ft
Engine Mount Bracket-to-Engine Mount Retaining
Bolts
60 N.m 44 lb ft
Engine Mount Retaining Nuts 40 N.m 30 lb ft
Exhaust Flexible Pipe Bracket Bolts 40 N.m 30 lb ft
Exhaust Gas Recirculation Valve Adapter Bolts 25 N.m 18 lb ft
Exhaust Manifold Heat Shield Bolts 15 N.m 11 lb ft
Exhaust Manifold Nuts 25 N.m 18 lb ft
Flexible Plate Bolts 60 N.m 44 lb ft
Flexible Plate Inspection Cover Bolts 10 N.m 89 lb in
Flywheel Bolts 35 N.m+30°+15° 26 lb ft+30°+15°
Flywheel Inspection Cover Bolts 12 N.m 106 lb in
Front Muffler-to-Main Catalytic Converter Nuts 30 N.m 22 lb ft
Fuel Rail Retaining Bolts 25 N.m 18 lb ft
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 1 of 330
http://www.eautorepair.net/app/PrintItems.asp?S0=2097152&S1=0&SG=%7BEEDCF... 3/30/2009
ENGINE MECHANICAL SPECIFICATIONS
Engine Mechanical Specifications
Intake Manifold Retaining Nuts 25 N.m 18 lb ft
Intake Manifold Support Bracket Lower Bolt-to-
Engine Block 40 N.m 30 lb ft
Intake Manifold Support Bracket Upper Bolts 25 N.m 18 lb ft
Lower Timing Belt Cover Bolts 10 N.m 89 lb in
Oil Pan Retaining Bolts 10 N.m 89 lb in
Oil Pressure Switch 40 N.m 30 lb ft
Oil Pump Retaining Bolts 10 N.m 89 lb in
Oil Pump/Pickup Tube and Support Bracket Bolts 10 N.m 89 lb in
Oil Pump Safety Relief Valve Bolt 36 N.m 22 lb ft
Oil Pump Rear Cover Bolts 6 N.m 53 lb in
Power Steering Pump Mounting Bolts 25 N.m 18 lb ft
Power Steering Pump Pulley Bolts 25 N.m 18 lb ft
Rear Timing Belt Cover Bolts 10 N.m 89 lb in
Spark Plug Cover Bolts 3 N.m 27 lb in
Spark Plugs 25 N.m 18 lb ft
Thermostat Housing Mounting Bolts 20 N.m 15 lb ft
Throttle Cable Bracket Bolts 8 N.m 71 lb in
Timing Belt Automatic Tensioner Bolt 25 N.m 18 lb ft
Timing Belt Idler Pulley Bolt 40 N.m 30 lb in
Transaxle Bell Housing Bolts 75 N.m 55 lb ft
Transaxle Brace Bolts 40 N.m 30 lb ft
Transaxle Torque Converter Bolts 65 N.m 48 lb ft
Upper Timing Belt Cover Bolts 10 N.m 89 lb in
Valve Cover Bolts 10 N.m 89 lb in
Application
Specification
Metric English
General Data
 Engine Type 4 Cylinder - In-Line
 Displacement 1598 cm3 97.51 in3
 Bore Stroke 79.0x81.5 mm 3.1x3.21 in
 Compression Ratio 9.5:1
 Firing Order 1-3-4-2
 Maximum Power - At 6200 RPM 77 kw/103.3 hp
 Maximum Torque - At 3400 RPM 145 N.m 106.9 lb ft
Cylinder Bore
 Diameter 79 mm 3.1 in
 Out of Round - Maximum 0.0065 mm 0.00025 in
 Taper - Maximum 0.0065 mm 0.00025 in
Piston
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 2 of 330

Jan 07, 2009 | 2004 Chevrolet Aveo

Not finding what you are looking for?
2004 Chevrolet Aveo Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...