Question about Cars & Trucks

Open Question

Car door bent back too far now won't close. Do I need a new door or can I fix it?

Posted by Anonymous on


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i fix it the problem with the sensor on back passenger door it shows up on dash board as door is open

Many door open sensors self-adjust the first time the door is closed. If something gets between the door jamb and the button switch, the switch can get pushed in too far to actually make the connection when the door is closed.
You may be able to pull the switch back into normal position, or at least replace the switch.

May 15, 2015 | 2005 Renault Megane Scenic

2 Answers

Car door bent back too far now won't close. Can I fix it myself, or how much will it cost

you will have to take to a shop they will have to remove the door and strighten the post that the hinges are on and more likley have to replace the door

May 24, 2014 | 2003 GMC Yukon XL

1 Answer

Car door won t close

the door is sprung. take it too a shop and hav them fix it. u will not be able to do a thing about it u r self. and turn it into the insurance people. lol.

Apr 13, 2014 | 2012 Chevrolet Traverse LS 4dr SUV 3.6L V6...

1 Answer

Door henge bent

As I understand it the was open at the time and was forced further open towards the front of the car? I think your door pillar was twisted around. In a new car the body shop might cut out the door pillar and weld in another, but I think that is mot the way here.
What you want is for the door to shut evenly in the body all round. There is a small amount of adjustment available in the door hinge attachment bolts, body side and door side, and in the lock striker plate. See here p23

It may be that a little adjustment in all these would be enough to fix the problem. Try that first.

If not, take the offending door off and look carefully at the A pillar. It does not take much distortion to prevent the door from closing properly. Compare it with the good side, using a long ruler to see where it should line up with the surrounding body. This will give you a target for straightening it.

Then you need a metal bar like this U channel, 2-3 ft long by about 3 in wide.

Hardware shops sell them. Drill holes in one end to match the door hinge bolt holes, and bolt it on to the door pillar, first one hinge then the other. Use it to carefully twist the door pillar back the other way, not too much, using the long ruler as a guide.

This should bring the door pillar back to where the manufacturer's adjustment takes care of the rest.

Dec 19, 2012 | 1999 Toyota Camry

1 Answer

My car door won't line up so i can close it

try jaking the door up a couple of inches passed the body line then release the jack and it should line up close enough to close the going past the body line it will bend the hinges back close to where they should be. hope this helps, as it has for me.

Feb 23, 2012 | 1999 Holden Vectra

1 Answer

The drivers-side back door of my 1998 jeep cherokee won't close. The latch has turned too far and won't go back to it's open position so, unless there is some trick you can recommend, it will...

since the door is open,, hold the handle in the open position and try and move the little hook looking latch , it may have just moved into the closed position , if you can move it to the open position, then your home free

Jul 04, 2011 | 1998 Jeep Cherokee

1 Answer

2005 Freestar "door open signal"

Chances are the autolock doesn't work because it "sees" a door open. Check the plunger between the door and the frame of each door to see if the plunger is broken, bent, or otherwise not working.

Jun 05, 2011 | 2005 Ford Freestar

1 Answer

Fix 2002 buick rendezvous side view mirror

it sounds like the mounting bolts embedded in the mirros housing were pulled out somewhat.You will not know untill the mirror is removed. If the studs that hold this mirror housing to the door are pulled out take a heat gun to get the studs warm and twist them back in flush. them apply JB Weld to the studs lowest part to the mirror housing so they stay secured

Feb 06, 2010 | 2002 Buick Rendezvous

1 Answer

Automatic door will not shut

check the track arm and roolers assembly for any distorsion in shape,

Sep 30, 2009 | 2001 Honda Odyssey

1 Answer

My altima 05 gas fuel door cover doesnt want to

Hello and thank you for using FixYa

The most common thing is that the fuel door is bent. This normally happens from opening the door to far or slamming it. You can try to manually bend it around to try to straighten it. If that does not work, then the gas door will need to be replaced and painted to match you car.

Thanks Jay!

Jul 17, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides