Question about Cars & Trucks

1 Answer

How to adjust Dg11100 car amp - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

If your head unit has an amp gain, turn it up as high as it will go. If it is hooked up to subs, the head unit will say subwoofer output in the menu. Then take a small screwdriver and turn the amp gain on the side of your amp counterclockwise to zero. Turn your freq. up to about a third. Crank your system up, with a song with good bass, and slowly turn your gain up till the bass from the subs sound distorted, and back it back down. If the bass is drowning out the other speakers in your car, then turn the gain down some more. I find it works best if you have your trebble up high, your mid range at a little less than half. And your bass at zero or one. Your amp is cranking up the bass, so let your other speakers handle the rest. This allows it to sound clearly at higher volumes.

Posted on Jan 02, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust a quadrajet carburetor?


You can only adjust the two idle screws,
unless your rebuilding it,then the instructions
will show you lots of adjustments

I would install a new float,regardless of how it
work now,as they get saturated & sink

The adjustment is the same as with all carbs

You start at about one turn out on the screws
& end up at about 1 3/4 turns

You try for the highest vacuum reading & then go
in about 1/8th turn

Have the vacuum advance hose of the dist & plugged

After the carb-- recheck your initial spark with the hose
off the dist

Vacuum gauge has to be from a manifold source,not
ported

(below the carb bottom throttle plates)

Oct 07, 2014 | Cars & Trucks

1 Answer

What all do i need to adjust transmission bands in 2001 dodge dakota


Bands are adjusted when you build a transmission

You do not need to adjust

The amount of band thickness & wear, is so small,
that the trans is shot, long before you have any wear
that needs to be adjusted

If you turn the screw the wrong way, the band falls off at
the ends & you can't reach in there to replace it & the unit
has to come out & apart

You will see no difference if you brought that band down tight
on the drum & then loosened it the correct number of turns

The servo will apply the band & there is no reasons for a delay

Your 2001 is 13 years or more old

If the fluid has not been changed every 2 or 3 years
since new,it is about to expire

Aug 18, 2014 | 2001 Dodge Dakota

1 Answer

Do a 06 charger daytona have bands to adjust


You only adjust transmission bands, when building the unit

By the time they have to be adjusted, the bands are worn &
the trans is shot & in need of a rebuild

Jul 22, 2014 | Cars & Trucks

1 Answer

Needed torqur spec on rocker arms on 1994 gmc 5.7liter


There is no torque spec for rockers. You tighten until there is no backlash, then preload another 1/4 to 1/2 turn. With #1 at TDC on the compression stroke, you adjust #1 by this procedure. You can also adjust intake valves on #'s 2, 5 & 7 as well as exhaust on 3's 1, 3, 4 & 8. Then rotate the engine until #6 is TDC on compression stroke and adjust intakes on #'s 3. 4. 6 & 8 and exhaust on #'s 2, 5, 6 & 7. Good luck.

Oct 01, 2013 | Chevrolet Cars & Trucks

1 Answer

How do you adjust the rear brakes on a 1990 Olds 88 Royale


Have to remove the rear brake drums &
turn the star wheel at the bottom
I think you need to take them completely
apart & clean & lube things, as they are self
adjusting & not doing so

Aug 10, 2013 | 1990 Oldsmobile Eighty Eight

1 Answer

Wheel alignment


If the car is stock then I would run the caster at .05 higher on the right than the left to adjust for the crown of the road. the front alignment looks good other than I am not sure which one is camber and which one is caster. To adjust the rear camber on these cars you have to have a camber kit. From the angle I am seeing you don't have a camber kit. Also the only way to adjust caster on the civic is to shift the sub frame.

Jul 30, 2013 | 1997 Honda Civic

1 Answer

My car is idleing high, and I need to adjust the idle


The car computer adjusts the idle

Check to see if there is an AIR Idle Control Valve
at base of throttle body-- that you can remove & clean

I'm not a Euro guy sorry

Try You Tube Video & put in your veh & question

Nov 20, 2012 | 2000 Volvo V40

1 Answer

How to adjust a rack & pinion on a dodge caravan 2000


there is no adjustment on chrysler rack & pinion,

Dec 10, 2011 | 2000 Dodge Caravan

1 Answer

How do you adjust the transmission bands in a 1991 dodge spirit 2.5 turbo with an automatic transmission?


The only one you can adjust is the low reverse band & it is accessed by removing the transmisson pan. You will need a feeler gauge & a wrench to adjust it. You can get the proper adjustment data from Chilton or Haynes manuals. Good luck!

Nov 19, 2010 | 1991 Dodge Spirit

1 Answer

What are timing marks on 2001 kia rio 1.5 engine


3-13 Degrees
Application:
With manual transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connect jumper wire
between ground & engine test terminals.
After completing adjustment, remove jumper wire.
Curb idle speed (750 RPM) transmission in drive.

3-13 Degrees
Application:
With automatic transmission

Note :
Before top dead center, at specified curb idle speed.
Locate data link connector & connector jumper
wire between ground & engine test terminals.
After completing adjustment, remove jumper wire.
When adjusting idle speed, set parking
brake & chock drive wheels.
Curb idle speed (750 RPM) transmission in neutral

Aug 18, 2010 | Kia Rio Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...