Question about 2008 Ford Escape

Open Question

How to remove water pump drive pulley on 2008 Ford Escape

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

Ad
messstat
  • 365 Answers

SOURCE: Water Pump Drive Belt

there is no water pump drive belt...there's a "Serpentine" belt that powers ALL the accessories and cooling...If you've never done this before, take it to a mechanic (NOT THE DEALER) and have it done ($75)
Good Luck

Posted on Jun 23, 2009

MNfisherman
  • 11896 Answers

SOURCE: How to remove water pump drivebelt on 2005 Escape

If there is no tensioner pulley then you will have to pry it on and off or remove water pump.

Free manual if you go to autozone..com and register.
or go to google ebooks and find a free chiltons manual.

Posted on Oct 06, 2009

  • 84 Answers

SOURCE: ABS & traction control just went out on 2008 Ford Escape.

Chances are it is a bad ABS sensor. Need to get scanned to know for sure and which one.
Not much i know but I hope that helps.

Posted on Feb 03, 2010

  • 312 Answers

SOURCE: Ford Escape 2003. Engine suddenly overheat.

Engine over heating can be caused by a number of things. When you say the water pump and radiator appear to be ok I am also guessing that you checked the coolant level to make sure it is normal.

If the level is low then you obviously have a leak. Insufficient coolant circulating will not cool the motor properly because it won't be able to draw enough heat out. If the level is normal then you need to check the thermostat to make sure it is opening properly. To do this, run the motor to temperature and check the top and bottom hoses. They should both be hot and firrm once the thermostat opens meaning the circulation loop is operating properly. If the top is hot and firm and the bottom is cold/soft or collapsed then the thermostat isn't opening.

If the thermostat is operating properly then you ned to look for some other obstruction or cause for coolant loss. Check the head/intake gaskets, hose connections, hoses, over flow tank, radiator fins, radiator side tanks etc..

Good luck.

Posted on Jun 10, 2010

Testimonial: "Thank you for your quick response. I will get the head/intake gasket checked."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the coolant pumb in ford escape 2012?


have you looked under the hood for the radiator hoses .bottom one goes to the pump

Sep 10, 2016 | 2012 Ford Escape

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

1 Answer

Where is the fuel pump driver module on a 2008 Ford Escape


on the bottom of the car near the gas tank, looks like a small square box with wires connected to it.

Jul 22, 2012 | 2008 Ford Escape

1 Answer

Serpintine belt diagram


what engine? Please rate if it helps

3.L v6

snorkelbobby_26.gif Item Part Number Description 1 3A733 Power steering pump pulley 2 8620 Drive belt 3 2E884 A/C clutch pulley 4 6316 Crankshaft pulley 5 6B209 Drive belt tensioner 6 10344 Generator pulley


2.0L Zetec 4 cyl with A/C

snorkelbobby_27.gif Item Part Number Description 1 10344 Generator pulley 2 19A216 Belt idler pulley 3 3A733 Power steering pump pulley 4 6C301 Drive belt 5 2E884 A/C clutch pulley 6 6B320 Crankshaft pulley 7 8509 Water pump pulley 8 6A228 Drive belt tensioner

Jan 12, 2011 | 2002 Ford Escape

3 Answers

Power steering went out on a 2008 ford escape. How do I fix it?


2008 escape power steering just went out. Need to know how/ what to get to fix it cheaper then ford dealership. They say I need a steering column

Nov 03, 2010 | 2008 Ford Escape

2 Answers

Serpentine belt diagram 2002 ford escape picture of serpentine belt pattern


CLICK on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/2002/make/ford/model/escape/2002_ford_escape_drive_belt_routing_diagram.htm

Feb 27, 2010 | 2002 Ford Escape

1 Answer

How to remove water pump drivebelt on 2005 Escape


If there is no tensioner pulley then you will have to pry it on and off or remove water pump.

Free manual if you go to autozone..com and register.
or go to google ebooks and find a free chiltons manual.

Oct 06, 2009 | 2005 Ford Escape

2 Answers

How do you change the water pump on a 1998 Ford contour 2.0 liter. have the part off but can't get it out of engine compartment


Removal
  1. NOTE: Install the memory saver.
    Disconnect the battery ground cable.
  1. Drain the cooling system. Refer to Cooling System Draining, Filling and Bleeding in this Section.
  1. Remove the wheel.
  1. Remove the right - hand side lower splash shield.
    1. Remove the bolts.
    1. Remove the splash shield.
    v2401032.jpg
  1. Lower the vehicle.
  1. Loosen the water pump pulley bolts.
    v2401027.jpg
  1. Remove the accessory drive belt. For additional information, refer to Section 303-05.
  1. Using the special tool, remove the crankshaft pulley.
    e0008816.jpg
  1. Remove the water pump pulley.
    1. Remove the bolts.
    1. Remove the pulley.
    v2401028.jpg
  1. Remove the water pump bolts.
    v2401029.jpg
  1. NOTE: Water pump must be turned 180° to remove from the vehicle.
    Remove the water pump.
    gq0214a.jpg

Apr 27, 2009 | Ford Contour Cars & Trucks

1 Answer

Serpentine belt diagram for a 5.9 diesel with air and 9 pulleys


5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Sep 13, 2008 | 2008 Dodge Ram 3500

Not finding what you are looking for?
2008 Ford Escape Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...