Question about 2000 Ford F250 Super Duty Crew Cabs

Open Question

What size is the nut on lower ball joint 7.3

Size of the nut on the lower ball joint assembly

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fyrebyrd1
  • 121 Answers

SOURCE: repair lower ball joints

The front lower ball joints are pressed into the steering knuckle. Once the brake components are removed, the CV shaft nut and tie rod ends can be removed. Remove the front strut bolts, and the lower ball joint nut. Separate the lower arm from the ball joint. Once the knuckle assembly is off the car remove the lower joint snap ring and dust boot. Utilizing a ball joint press (should be able to rent from local parts store) press the joint out of the knuckle. Re-installation is naturally reverse of removal. I hope this helps.

Posted on Nov 22, 2008

Ad
  • 408 Answers

SOURCE: replace lower ball joints

if you have some mechanical knowledge, it is not really difficult.  It is just time consuming.  Pick up a Haynes manual and they will give you a step by step with pics in doing this.

Posted on Mar 07, 2009

SUPERMAN_B_1
  • 294 Answers

SOURCE: REPLACING LOWER BALL JOINTS ON 2000 FORD F250 4X4 7.3L DIESEL

hello,yes you do have to take the hub off to replace the ball joint with the ball joint being on the back side of the hub. hope this helps and please rate this.

Posted on Mar 15, 2009

  • 204 Answers

SOURCE: How do you change upper and lower ball joints on 2001 Ford Expedition?

i am not going to lie to you on this. if you do not have a very good mechanical back ground you should not attemp this procedure your self because it could result in serious injury. it should be brought to a shop because they do have the right tools to do this. alot of the time ball joints are pressed in under extream amounts of pressure

Posted on Apr 21, 2009

  • 19 Answers

SOURCE: removal and replacement of a

You will need certain tools to remove the ball joint. You will need a ball joint removal and installation kit you can find at a local automotive store.Remove brakes and control arms to easily get to ball joint and start the removal. The ball joint kit has instructions on how to remove and install your new ball joint.

Posted on Jul 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Replace lower ball joints. How do you replace Lower ball jonits?


REMOVAL & INSTALLATION
  1. Raise and safely support the vehicle, allowing the front suspension to hang free.
  2. Remove the wheel and tire assembly. WARNING
    Be careful when working in the area of the CV-joint boot. Damage to the boot could result in eventual CV-joint failure. If necessary, install CV-joint boot protector tool J-34754 or equivalent, to protect the boot.
  3. On Eldorado and Seville with 4.6L engine, remove the road sensing suspension position sensor from the lower control arm.
  4. Remove the cotter pin and nut from the ball joint stud. Use ball joint separator tool J-36226 or equivalent, on Deville and Fleetwood or ball joint separator tool J-35315 or equivalent, on Eldorado and Seville, to separate the ball joint from the steering knuckle.
  5. On Deville and Fleetwood, loosen the stabilizer bar link nut.
    1. Drill out the 3 rivets retaining the ball joint to the lower control arm and remove the ball joint. NOTE: Recommended drill-bit is 1⁄2 inch (13 mm). Fig. 1: Drilling the rivets out of the lower control arm 91048g05.gif
      Fig. 2: Installing the bolts in the lower control arm 91048g06.gif
      To install:
  6. Attach the new ball joint to the lower control arm with 3 mounting bolts and nuts.
    1. On Deville and Fleetwood, the bolts must be installed from the top of the control arm.
    2. On Eldorado and Seville, the bolts must be installed from the bottom of the control arm
    3. Tighten the nuts to 50 ft. lbs. (68 Nm).
    4. On Catera, the bolts must be installed from the top of the control arm.
    5. Tighten the nuts to 26 ft. lbs. (35 Nm).
  7. On Deville and Fleetwood, tighten the stabilizer bar link nut to 13 ft. lbs. (17 Nm).
  8. Connect the ball joint to the steering knuckle and install the castellated nut.
  9. On Deville and Fleetwood, tighten the ball joint nut to 88 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a tighten of 41 ft. lbs. (55 Nm) must be obtained.
  10. On Eldorado and Seville, tighten the ball joint nut to 84 inch lbs. (10 Nm). Then tighten the nut an additional 120°, during which a minimum torque of 37 ft. lbs. (50 Nm) must be obtained. If the minimum torque is not obtained, check for stripped threads. If the threads are okay, replace the ball joint and knuckle.
  11. On Catera, tighten the pinch bolt to 74 ft. lb. (100 Nm).
  12. Install a new cotter pin. If the cotter pin cannot be installed because the hole in the stud does not align with a nut castellation, tighten the nut up to an additional 60°to allow for installation. NEVER loosen the nut to provide for cotter pin installation.
  13. On Eldorado and Seville with 4.6L engine, install the road sensing suspension position sensor to the lower control arm.
  14. If necessary, remove the CV-joint boot protector tool.
  15. Install the wheel and tire assembly and lower the vehicle. Fig. 3: Separating the ball joint from the steering knuckle 84208016.gif
    Fig. 4: Lower ball joint installation - Deville and Fleetwood 84208017.gif
    Fig. 5: Lower ball joint installation - Eldorado and Seville 84208018.gif

Jan 17, 2011 | 1991 Cadillac DeVille

1 Answer

How to repair a lower ball joint on the passenger side


Hi.


jshreader_9.jpgjshreader_8.jpg

1. Raise and support vehicle.
2. Remove tire and wheel assembly, then install modified outer seal protector No. J34754, or equivalent, Fig.3 .
3. Remove lower ball joint cotter pin and nut, then loosen ball joint from steering knuckle using tool No. J-29330, or equivalent.
4. Position a suitable pry bar between suspension support and lower control arm and separate lower ball joint from steering knuckle. On some models, it may be necessary to remove nut attaching link to stabilizer shaft.
5. Locate center of rivet body and mark with a center punch.
6. Using a 1/8 inch drill, drill pilot holes completely through rivets. Using a 1/2 inch drill, drill final holes through rivets to ensure fitting of new ball joint.
7. Remove ball joint from lower control arm.
8. Assemble new ball joint to lower control arm with bolts provided in service package, Fig.9 . Tighten bolts to specifications.
9. Insert ball joint stud into steering knuckle and tighten nut to specifications, then install cotter pin.
10. Install wheel and tire and check front wheel alignment.

I hope this helps you.

Thanks.

Nov 28, 2010 | 1994 Pontiac Grand Prix

1 Answer

Need to replace ball joints


http://groups.yahoo.com/group/villagerquest/ Ball Joint Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the suspension lower arm ball joint cotter pin.
  1. Remove the suspension lower arm ball joint nut and separate it from the wheel knuckle.
May have to leave nut partially on and hit the nut hard with a hammer to knock the tapered stud down and out. May have to hit side of knuckle to help get it to drop. or rent a pickle fork to drive between the bal joint and knuckle.
  1. Remove the suspension lower arm ball joint to suspension lower arm nuts and remove the ball joint.

Nov 15, 2010 | 2001 Nissan Quest

2 Answers

How to fix a ball joint in a ford tempo


REMOVAL & INSTALLATION The lower ball joint is integral to the lower control assembly and cannot be serviced individually. Any movement of the lower ball joint detected as a result of inspection requires replacement of the lower control arm assembly.
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the nut and bolt securing the ball joint to the steering knuckle.
  4. Remove the nut and bolt securing the control arm to the vehicle sub frame. To install:
  5. Install the control arm assembly to the vehicle sub-frame using the nut and bolt. Tighten the nut to 69-86 ft. lbs. (93-117 Nm).
  6. Install the lower ball joint into the steering knuckle and secure it with the nut and bolt. Tighten the nut to 32-43 ft. lbs. (43-59 Nm).
  7. Install the wheel and tire assembly and lower the vehicle.
  8. Road test the vehicle.
prev.gif next.gif

Nov 06, 2010 | 1990 Ford Tempo

1 Answer

How to replace a lower ball joint on a 1988 pontiac grand prix hit a pothole and it popped out


Hope this helps and please don't forget to rate! Thank you!


e8fbd9d.gif
Front ball joint with heat shield

Remove and Replace-

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the front wheel and tire assembly.
  4. Unfasten the retaining bolts, then remove the ball joint heat shield.
  5. Remove and discard the lower ball joint cotter pin.
  6. Remove the ball joint nut.
  7. Loosen, but do NOT remove, the stabilizer shaft bushing assembly bolts.
  8. Separate the ball joint from the strut/knuckle assembly using ball joint/tie rod puller J-35917 or equivalent.
Do NOT damage the halfshaft boots when drilling out the ball joint rivets.
  1. Drill out the rivets retaining the ball joint to the knuckle strut assembly and remove the ball joint from the knuckle. Use a 1/8 in. drill bit. Refer to the instructions in the ball joint replacement kit.
To install:
  1. Position the lower ball joint in the strut/knuckle assembly.
  2. Install the four ball joint bolts and nuts, as shown in the ball joint kit and tighten to specifications.
  3. Install the ball joint-to-lower control arm. Install a new ball joint-to-lower control arm nut.
  4. Tighten the stabilizer shaft bolts to 35 ft. lbs. (48 Nm).
  5. For 1988-91 vehicles, tighten the ball joint-to-lower control arm nut 15 ft. lbs. (20 Nm) plus at least an additional 90° (11/2flats), plus enough to align the cotter pin hole. Do NOT overtighten.
  6. For 1992-96 vehicles, tighten the lower ball joint nut to 63 ft. lbs. (85 Nm). Tighten to align the next slot in the nut with the cotter pin hole in the stud. Do NOT tighten more than 60° (1 flat) to align with the hole.
  7. Install a new cotter pin.
  8. Position the ball joint heat shield and secure with the retaining bolts. Tighten to 62 inch lbs. (7 Nm).
  9. Install the front wheel and tire assembly, then carefully lower the vehicle.
  10. Connect the negative battery cable and check for proper suspension operation

Apr 26, 2010 | 1988 Pontiac Grand Prix

1 Answer

How do you put in a ball joint in a 2001 sebring convertible


It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

Mar 17, 2010 | 2002 Chrysler Sebring

1 Answer

2001 ford explorer sport


support vehicle under A frame remove wheel. loosen nut on top of ball joint.seperate spindle assembly from ball joint w/ball joint seperating tool AKA pickle fork.remove nut.ball joint is riveted to lower A frame-chisel off or drill out rivets.install new ball joint w/nuts &bolts supplied with it

Sep 22, 2009 | 2001 Ford Explorer Sport

1 Answer

How to replace right front axle 2000 buick lesabre


Lift the passenger side of vehicle. Remove tire/wheel assembly. Remove the axle nut. Remove the tie rod end nut. Smack the side of the housing the tie rod end goes into to pop the tie rod end loose and out. Remove the sway bar link. Remove the lower ball joint nut. Smack the housing the lower ball joint goes into to pop the ball joint loose. Pry the lower control arm down to pop the ball joint out. swivel the rotor and strut assembly to the side. Pop the axle out. Reassemble in the reverse order.

Jul 05, 2009 | 2000 Buick LeSabre

1 Answer

How to change lower ball joints


part of lower arm assembly only.

Installation
  1. Inspect lower ball joint boots and seals for damage and replace if required. Lower ball joint and seal is part of front suspension lower arm and must be replaced as an assembly.
  1. NOTE: Do not tighten the front suspension lower arm bolts and nuts to the specified torque until the end of assembly. Install nuts and tighten until snug.

    Position the front suspension lower arm in the front crossmember. Install the bolts. Install the nuts and tighten until snug.
  1. Install torsion bar. Refer to Torsion Bar in this section.
  1. Raise the front suspension lower arm to allow installation of front suspension lower arm ball joint into spindle bore.
  1. Lower front suspension lower arm with a jack while making sure lower ball joint is seated in spindle bore. Install the lower ball joint attaching nut and tighten to 113-153 Nm (82-113 lb-ft). Install a new cotter pin.
  1. Raise vehicle. Position the front shock absorber and install the nut/washer/bushing assembly. Tighten nut to 40-55 Nm (30-40 lb-ft).
  1. Install the two nuts attaching the front shock absorber to the lower control arm and tighten to 21-29 Nm (15-21 lb-ft).
  1. NOTE: Front suspension lower arms must be in the horizontal or curb position (vehicle on the ground) when tightening the front stabilizer bar link bolts. Use jackstands to raise the front suspension lower arms to the horizontal position or lower the vehicle to the ground (curb position).

    Lower the vehicle to the ground.
  1. Connect the stabilizer bar link bolt to the front suspension lower arm and tighten to 13-17 Nm (10-13 lb-ft).
  1. Tighten nuts and front suspension lower arm bolts to the No. 1 crossmember to 150-200 Nm (111-148 lb-ft).
  1. Check ride height and align as necessary. Refer to Section 04-00 .
  1. Lower the vehicle.

Apr 17, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...