Question about Cars & Trucks

Open Question

Rear wiper operates when I unlock my Peugeot 206sw

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

muntejaya
  • 10421 Answers

SOURCE: peugeot 206sw blower will only

Hi,
Your blower is still OK. The problem are on your selector switch and or power cable / supply. Please check and get them fixed.

Posted on Jan 18, 2011

  • 977 Answers

SOURCE: I have a Peugeot 206SW

the stoplights are activated by a switch near the brake pedal under the dash, the switch may have come loose & needs to be adjusted or the wire has come off,it could also be a blown fuse check the fuses in the fuse box,also check the wiring in the trunk for loose or disconnected wires......hope this helps......cheers.

Posted on Aug 10, 2011

Testimonial: "Exceptionally good service, it is now soarted Many Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 trialblazer rear window wiper inop. changed switch and motor. no power to motor. cannot find relay nor fuse


There are something's involved that you are not aware of , or familiar with . Electronic control modules .
Rear Wiper/Washer System Controls
• Body control module (BCM)
• Liftgate control module (LGM)
• Rear wiper/washer switch
Do you know what a serial data network is ?
Rear Wiper/Washer System Operation
The rear window wiper/washer switch is an input to the BCM. The requested rear wiper mode is sent to the liftgate control module (LGM) by the BCM as a message on the serial data circuit, and the rear window wiper motor is controlled by the LGM. The switch power circuit to the rear wiper/washer switch is a 12-volt reference supplied by the BCM during ignition on, accessory or RAP power modes. The rear wiper/washer switch is a series of resistors and the switch position is determined by the voltage of the rear wiper/washer switch signal circuit to the BCM. The rear wiper/washer switch has continuity at all times and the BCM expects a rear wiper/washer switch signal voltage in all switch positions including OFF. The rear wiper motor is supplied battery positive voltage and ground. The LGM controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the LGM. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode. The liftglass and liftgate ajar switches are inputs to the LGM and must be in an inactive state in order for rear wiper washer system operation to be enabled. When an ajar switch is active the LGM suspends wiper motor operation directly and sends the ajar switch status messages over the serial data circuit enabling the BCM to suspend washer pump operation. The rear window washer pump is controlled by the BCM through the rear washer relay. Battery positive voltage is supplied to the coil and switch sides of the rear washer relay. When the rear window wash request is active the BCM energizes the relay by grounding the relay coil through the rear washer relay control circuit. When the relay is energized battery positive voltage to the relay switch is supplied to the washer pump control circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
DTC B1017 or B3970
The rear wiper motor is supplied battery positive voltage and ground. The liftgate control module controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the liftgate control module. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode.
DTC B3799

2
Turn the ignition ON.
Operate the rear wiper switch through all the switch positions.
Does the rear window wiper operate normally?
--
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Install a scan tool.
Display the liftgate control module data list.
Observe the following parameters while operating the respective switches. Refer to Scan Tool Data List for typical values.
• Liftgate Ajar Switch
• Liftglass Ajar Switch
Did the scan tool indicate the correct switch positions?
--
Go to Step 4
Go to Courtesy Lamps Inoperative in Lighting Systems
4
Observe the requested rear wiper parameter in LGM data list.
Operate the rear wiper switch through all the switch positions.
Does the scan tool indicate the correct requested rear wiper parameter in relation to the switch position?
--
Go to Step 5
Go to Step 6

Feb 06, 2017 | 2002 Chevrolet TrailBlazer

1 Answer

Why won't my peugeot 206sw start an it has locked gears


Try turning steering wheel some each way while trying to turn key, pressure from steering may not be allowing it to unlock to let key turn. Other cars sometimes do that, if the locking wheel is gear you are talking about.

Jul 08, 2016 | 2004 Peugeot 206 SW

1 Answer

Peugeot 307 est. rear wiper removal


get a new 1 or check the breakers yards

Aug 26, 2014 | Peugeot Cars & Trucks

1 Answer

How will I operate so that the wiper at the back will move?


The windscreen wiper stick attached to the steering wheel column has two functions. The up and down movement is to control the operation of the front wipers and a small ring collar that rotates on the wiper stick handle to control the rear wipers.

Hope this helps. You can get a manual from this site and check on page 110 http://www.scribd.com/doc/43174930/peugeot-206-2005-2006-manual

Aug 02, 2014 | Peugeot 206 Cars & Trucks

1 Answer

Peugeot 206sw wont start and is makin chain noises from engine and also air filter is jumpin any ideas plz thanx clare.


check the timing belt first sounds ominous this but without my head under the bonnet i have no idea

Jan 30, 2013 | 2005 Peugeot 405

2 Answers

I have a Peugeot 206SW and the brake lights have stopped working can you advise please Many Thanks


the stoplights are activated by a switch near the brake pedal under the dash, the switch may have come loose & needs to be adjusted or the wire has come off,it could also be a blown fuse check the fuses in the fuse box,also check the wiring in the trunk for loose or disconnected wires......hope this helps......cheers.

Aug 10, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

Peugeot 206sw blower will only operate on switch p[osition 4


Hi,
Your blower is still OK. The problem are on your selector switch and or power cable / supply. Please check and get them fixed.

Jan 18, 2011 | Peugeot 405 Cars & Trucks

1 Answer

I have a orange warning light on the dash. what


this attention warning tell u that ur car has to be taken to a peugeot garage or specialist to analyse this lamp function and repair it.

Aug 13, 2009 | Peugeot Liberte Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...