Question about 2008 Ford Fusion
My driver side door will not open from inside of the car. How do I fix the problem
You will need to remove the door handle, but you may have to pull the door trim plate first. Pull the handle assembly outward and inspect it to make sure the inner door connector rods are attached. These are held in place with plastic pieces, and plastic parts on the door handle. Replace the handle if the rod loop is broken. Replace the door rod ends with new hardware. This can all be done in your driveway, and requires very little mechanical knowledge or skills.
Posted on Jan 02, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 99 Ford explorer Door Lock
OK. Now I have come across this myself and have done the following to fix it. First you need to know if the power door lock actuator is bad or not. If the driver door locks and unlocks with the inner driver door main control switch then it is not bad. If not then try to replace this component. To do this you will need to remove the door panel. It is not that hard. Many tutorials online that can help with this. It is easier then you think. Pull back the inner water seal from the door frame to gain access to the inner working of the door. You will need to remove the window track that is in front of the actuator to remove it easily. If not then you will have a very hard time trying to figure out how to get it out. There is a bolt that hold the bottom half on that needs to be removed. It comes out and re installs very easily. Disconnect the wiring from the actuator before you try to remove it. You will need to remove the rivet located on the outside of the door that holds the actuator in place. Drill this one out. This needs to be removed so the old actuator can be removed and you can install a new one. This rivet is heavy duty is going to be 1/4" You must not use a nut an bolt or a plastic rivet to reinstall the new actuator for the nut an bolt can come loose and cause failure and the plastic one can break very easily due to the power that is exerted by the actuator. You will have to get a heavy duty rivet gun for this as well for the standard ones are too small. They can be had at Harbor Freight for like $20.00 and comes with all the different size rivets too. To re install the new actuator just reverse the process. If this does not fix it then the problem lies with the door cylinder contact switch. This switch is mounted on the Keyed door cylinder and is connected to the power door lock actuator. It sends a signal to the actuator to lock or unlock when you turn the key. It also controls all the the other doors as well. I am not certain how much this is but I do know it can be purchased at most auto parts stores. I have also found that the door latch receiver mechanism can go bad too. The key will lock the driver side door but wont unlock the driver side door. The only way to open the door was to go to the other side or the rear driver side and use the inner door lever. This can be a costly fix and is not easy to replace by yourself. It is very difficult to remove and can be a lengthy job at that if you are not to familiar with these types of assemblies. If you are not careful you can also break the inner door handle by pulling too hard and that is not cheap to replace either. If you do not want to try to do this yourself then let someone who knows how to do it do it for you. It can be a very aggravating job if you are not used to it. If your key is not turning in either direction on any of the locks then the tumblers are jammed and need to be lubed up to operate properly. This is very easy to do and won't take much time. To remove the key lock from the door you need to remove the lock ring on the cylinder to disengage the door lock mechanism and then pull the flex plate that holds the lock in the door. After that insert your key to see if the tumbler slides are moving freely. If not then spray it with an all purpose oil or grease so you can loosen up the tumblers slides. They should be visible on the underside of the lock. Work the key in an out slowly till you see all the slides move easily and watch to make sure that they go back in to place when you remove the key. That's all there is to it. If any of the tumbler slides are damaged then you need to take it to a lock smith and have him replace the bad slides. Should not cost that much and will save you some money as well instead of paying for a new keyed lock which will also change your key to that door and will not work in the other ones. Hope this helps
Posted on Jan 04, 2009
I checked Ford Focus mirror replacement and it seems to be the same. This is for the manual, unheated mirror.
Remove the mirror cover inside the door - slide a screwdriver behind the cover and pry loose carefully.
Remove the single 10mm bolt and the mirror comes free.
NB. Do not drop the bolt into the door.
Posted on May 22, 2009
There is a triangular piece, at top corner, covering a screw behind the mirror. Remove that screw. Remove the piece that covers the handle and remove the screw holding the handle to the door. Look through, where door handle was and remove another screw just above where the handle was. This screw is holding the panel to the actual door. Pop the cover off for the automatic door locks and disconnect them. Lift the panel in an upward direction.
Posted on Nov 14, 2009
Tips for a great answer:
Jan 27, 2016 | Cars & Trucks
Jan 21, 2013 | Cars & Trucks
Dec 05, 2012 | 2006 Buick Rendezvous
Jul 07, 2011 | 2006 Chevrolet Impala
Jun 10, 2011 | 2006 Buick Lucerne
Jun 17, 2010 | Cars & Trucks
Jun 16, 2010 | 2002 Saturn Sl
Oct 21, 2009 | 1997 Hyundai Elantra
Jul 16, 2009 | 2003 Hyundai Tiburon
May 03, 2015 | 2008 Ford Fusion
1,077 people viewed this question
Usually answered in minutes!