Question about Cars & Trucks

1 Answer

1982 280zx datsun wont start from problem coil

Replaced coil and still no fire

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 21 Answers

It has a CDI or a Delco? check for voltage in ign.coil, and the breaker points gap.

Posted on Jan 02, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
cj5470110
  • 41 Answers

SOURCE: 87 prelude has no fire from coil, replaced it an still same thing

check to see if the wiring harness connecting to the plug is not corroded.

also if all connections are good then your next step lies with the ignition control module.

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the head gasket in my 82 nissan datsun 720 now it wont start has fire and gas getting to it how do i fix it


My guess is you have gotten the cam or ignition timing off during reassembly. datsun Series head replacement part 1
This video shows the proceedure. Watch it and see where you went wrong.

Apr 03, 2016 | Nissan Cars & Trucks

1 Answer

Coil wont fire all three wires have power but no fire to plugs replaced twice


Crank sensor if it has one,timing belt skipped is a possibility,and always the dread security key problem.don-ohio

Apr 01, 2013 | 2001 Ford Focus

1 Answer

No fire to sparkplugs


Bit late here, but I love Datsuns! First check if you are getting power to coil on the + side of coil. Pretty much a straight path from ignition switch to coil. Then pull off coil to distributor cable at the distributor and check for spark on that wire when cranking engine over. If good, rotor, distributor cap, plug wires, or sparkplugs need checked. If no spark from coil, it should be tested with an ohmmeter for proper resistance values, or swap in another coil.
Does it have mechanical points and condenser or electronic ignition?

Nov 22, 2012 | Datsun 510 Cars & Trucks

1 Answer

Datsun 180b wont keep running


Replace the ballast resistor on the coil.

Mar 19, 2012 | Datsun 1600 Cars & Trucks

2 Answers

I have been given an old Datsun 720 4x4 ute. I t has been sitting idle for some time and when it did run it was rough. I have replaced the carby as the old one is rusted up, but it wont run,unless you poor...


hi, take the fuel line off and turn it over, fuel? make sure you have a fire extinguisher there fuel pump and fuel filter a must, if it still wont run after that then stuck needle valve. Oreally sells a carb rebuild kit for I think. or junkyard cool truck, rare 4x4, keep it
jm

Aug 23, 2010 | Datsun 720 Cars & Trucks

1 Answer

Firing order Datsun 710 (4cyl. L20B engine)


Remove the rocker cover.
Turn the engine until it's at TDC on No.1
Both No.1 rockers should be loose.
Remove distributor cap and look where rotor is pointing, this is No.1 plug lead.

Dec 23, 2009 | Datsun 720 Cars & Trucks

1 Answer

1978 datsun 280 z back firing and sputtering through first 3 gears what can i do


This is an ignition problems, check the setting of platina gap and optimal position, clean the spark plugs and check the coil.

Sep 06, 2009 | Datsun 310 Cars & Trucks

1 Answer

Need a diagram of the firing order for 1972 datsun 510


Turn your crank pulley and line the timing marks to top dead center,pull the distribuor cap and see where the rotor points to, thats where the #1 position is located.

Apr 08, 2009 | 2003 Datsun 510

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...