Question about Cars & Trucks
Nothing works but head lights
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1999 CONCORDE: check the battery terminals probably they are not tight enough...something like that happened to me just the lights turned on and the car seemed to be dead, the battery is still ok since then. I just needed to buy new terminals.
Posted on Nov 25, 2008
the jetta has a faulty alarm system from the factory i have been working on one in my shop. the alarm moddule is inside the dash behind the light switch and has a 10 pin connector and a 6 pin connector. this can be bypassed if you disconnect both connectors and jump the two large wire on the 6 pin connectors, these wires operate your starter. the car will start and run but your alarm will no longer be active. the door locks and everthing else will still work. the only issue i am having is the factory radio isn't working because it is controlled by the alarm. but worse case scenario i can use an aftermarket radio if need be.
Posted on Feb 28, 2009
SOURCE: jeep alarm will not turn off
The ignition security on/off is located at the trunk lock. unlock and lock rear gate and the alarm will turn off. My jeep sat in my drive for a month before a jeep tech told me this. It still triggers the security sometimes when I unlock the passenger door with the key and I go straight to the rear gate lock and it shuts off instantly.
Posted on Dec 13, 2009
yes theres is, try locking and unlocking the pass/side door with the key. you can check for power at the starter at the small wire if theres power at that wire when the key is held in the crank position then you have a bad starter try taping on starter while key is held in start if its starts when tapping then starter is bad,heres a diagram to show you were to tap and where to check for power, hope this helps.
Posted on Feb 10, 2010
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment
Posted on Mar 08, 2010
Tips for a great answer:
Dec 05, 2014 | 2000 Chrysler Cirrus
Jun 12, 2017 | Volkswagen Jetta Cars & Trucks
Sep 08, 2011 | 2005 Kia Sorento
Jul 11, 2011 | 2001 Oldsmobile Aurora
Mar 08, 2010 | 2004 Dodge Durango
Feb 15, 2010 | 2000 Chrysler Grand Voyager
Dec 29, 2009 | 2001 Chevrolet Cavalier
Mar 20, 2009 | 1996 Chevrolet Blazer
19 people viewed this question
Usually answered in minutes!