Cars & Trucks Logo

Related Topics:

Alberto G. Posted on Jan 01, 2013

Repair was done, now how long does it takes for code C1155 to clear

I replace LF speed wheel sensor , but code C1155 still shows on my scanner

4 Related Answers

Anonymous

  • 299 Answers
  • Posted on Jun 17, 2009

SOURCE: HOW TO REPLACE OR REPAIR WHEEL SPEED SENSOR

It is part of the bearing hub assembly.Very have to do without air tools,If setting multiple abs/tc code (wheel speed sensors) probably abs electronic module or chaffed wires on drivers side at ac lines by air box.Have big problems with this and probably will come back.

Ad

Philip Armitage

  • 437 Answers
  • Posted on Sep 05, 2009

SOURCE: 2001 Buick Century with code p1232 LF wheel speed

wire going to sensor breaks inside the insulation the plug may look ok by looking at it but if you grab hold of one wire at a time right where they go into the connector on the wheel sensors and give a good tug. If wire pulls away from the connector then it means that the connector is bad and wire was broken behind the insulation

Anonymous

  • 231 Answers
  • Posted on Sep 19, 2011

SOURCE: 94 Grand Prix ABS issue.

Speed sensors commonly go bad and need to be replaced. If you replace the bad sensor it should solve your problem. I hope this helps and if you have any other questions please feel free to ask.

shadow_ri775

Rob Cabs

  • 274 Answers
  • Posted on Sep 12, 2012

SOURCE: c1155

is there continuity in the circuit, check to make sure a wire isnt broken or loose

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Intermittent abs light

What make , model an year vehicle ? Is the wheel speed sensor integral to wheel bearing hub or separate ? Could be a corroded tone ring on half shaft . ABS activates on every stop damaged tone ring
2helpful
2answers

I had a friend /backyard mechanic change my lower ball joints and LF hub assembly. Now my ABS light is on and the ADVTRAC won't turn on. 05 Mountaineer 2wd. Why?

anytime the suspension system needs to be repaired, its crucial that a wheel alignment is done. because the computer is so precise in its measurements of wheel speed; which facilitate systems like abs/traction control, even the slightest value being out of spec could and most likely will result in failure of these systems. get an alignment. hope this helps!
0helpful
1answer

2006 ford crown vic abs code b1596

B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .
1helpful
1answer

C1155

is there continuity in the circuit, check to make sure a wire isnt broken or loose
0helpful
2answers

94 Grand Prix ABS issue. My abs light is on so i scanned it and the codes came up RF wheel speed sensor 0 speed. LF wheel speed sensor excessive speed. Now, when I put the car up and let the wheels spin...

quite easy throw the code reader away for a start then work from basics ,disconnect each sensor in turn and check for continuety ,also the wiring connections for corrosion then if all the sensors check out then you check the toothed rings that the sensors pick up on and make sure they havent corroded away or come loose on the drive shafts especialy the front drive shafts as this is a common fault on vehicles used in northern climes where their is snow and wet rain
1helpful
2answers

2006 X Type engine light c1155

C1155 LF input circuit what it mean is left front speed is not producing a circuit okay it produces its own voltage and send it out to the ABS module basically it at it useful life
0helpful
1answer

Abs kicking in at low speeds no light on 3codes stored and cleared c1145,c1155 , c1178 . have checked rear relucter discs on c.v joints o/s and n/s intact / removed sensors for better look, ok corroded...

C1145 RH Front Speed sensor cct poss faulty sensor.
C1155 LH Front Speed sensor cct poss faulty sensor.
C1178 Unknown

Sorry can't be any more help than this
4helpful
3answers

What is a c1145 code and c1155?

the error codes you are looking for are

C1145 Speed Wheel Sensor RF Input Circuit Failure
C1155 Speed Wheel Sensor LF Input Circuit Failure

there are many reasons this could be if you recently had tires changed or rotated. it would be good to make sure they did not leave them disconnected. Best to take it to a professional and have it checked out as these are important sensors.
thanks and have a great day
11helpful
1answer

What is service codes P1111, C1145, C1155, C1165, C1175?

HI. The codes and their respective definitions are below:


P1111 Intake Air Temperature (IAT) Sensor Circuit Intermittent High Voltage
C1145 Front right wheel speed sensor input circuit failure
C1155 Front left wheel speed sensor input circuit failure\
C1165 Rear right sensor - trigger monitoring
C1175 Rear left sensor - trigger monitoring
Not finding what you are looking for?

267 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...