1999 Chrysler Concorde Logo

Related Topics:

A
Anonymous Posted on Jan 01, 2013

My chrysler concorde lxi will not go into reverse or any other gear

My car won't move out of park. the gear shift moves fine but doesn't engage.

5 Related Answers

Anonymous

  • 3 Answers
  • Posted on Dec 01, 2008

SOURCE: I have a 98 Concorde

You need to check the linkage. Under the car, the section that connects the gear shift stick to the transmission rods.

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Jun 22, 2009

SOURCE: My gear shift is stuck and will not move from park

do the brake lights work? the system has a lock out that keeps you from moving out of park unless the brake circuit is activated, hence no brake lights no park lock out release, if the brk lights do work u most have a stuck or defective park lock out solenoid.

Robert Debison

  • 412 Answers
  • Posted on Aug 16, 2009

SOURCE: chrysler concorde car wont shift from reverse to park

it sounds like your gearshift cable is broken..if you can jack up vehicle and support it safely,get someone to move shifter and look on driver's side of transmission and see if linkage is moving on trans..linkage is up near top of trans..i have seen this problem before

Anonymous

  • 520 Answers
  • Posted on Sep 01, 2009

SOURCE: 2004 Chrysler Pacifica: Gear is stuck in park-

This car has several points on the transmission that look similar to the drain plug. If they removed the plug on the driver's side rear of the transmission, then they dropped a linkage from the transmission drive train and it is now sitting on top of the valve body instead of falling into place when you attempt to reverse. Have it checked by a certified transmission shop to verify this is the problem, then I would strongly advise you to make the lube shop pay for the repairs if it is. Hope this helps, good luck!

Anonymous

  • 381 Answers
  • Posted on Mar 29, 2010

SOURCE: 2000 chrysler concorde will not get out of gear.

Change the shift cable (cable from shifter to transmission) Also spray some WD40 on the shift linkage on the trans and work it back and forth to loosen it up before you put the new cable on. Good luck

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 Chrysler Concorde. We have had two cases recently where tried to shift out of park into any gear. Gear shift moved fine but nothing happens. Any ideas what might cause this inconsistent problem?

Transmission will have a more permanent problem soon. Have it serviced so the mechanic can diagnose the problem. It is definitely a problem in the future.
1helpful
2answers

2000 grand prix 3100 tran. didn't whine or slip and fluid doen'st smell burnt. But the car won't move it is like it is in N. all the time.

could be a selector failure. easiest to check first or internall drama with torqu converter ,one way clutch or other. these will require r@r n overhaul
1helpful
1answer

My 1998 Honda civic ex won't move but the motor

Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?
0helpful
2answers

I have a 2005 Chrysler 300, As I shifted the car from park to reverse I heard and felt a pop in the gear shift. The gear shift moves but the car is stuck in low.

Go to the Prindle switch where the cable meets the transmission and check if it has not unhooked. Move the shifter all the way to the Park position and adjust/tighten.
1helpful
1answer

Chrysler concorde car wont shift from reverse to park

it sounds like your gearshift cable is broken..if you can jack up vehicle and support it safely,get someone to move shifter and look on driver's side of transmission and see if linkage is moving on trans..linkage is up near top of trans..i have seen this problem before
4helpful
1answer

2000 chrysler concorde will not get out of gear. trans doesn,t skip or slam it drives fine. you just can't move the shift lever

Change the shift cable (cable from shifter to transmission) Also spray some WD40 on the shift linkage on the trans and work it back and forth to loosen it up before you put the new cable on. Good luck
9helpful
2answers

My gear shift is stuck and will not move from park to reverse. I had backed out the car and turned it off. when I went to move the car, my gear shift will not move out of the park position.

do the brake lights work? the system has a lock out that keeps you from moving out of park unless the brake circuit is activated, hence no brake lights no park lock out release, if the brk lights do work u most have a stuck or defective park lock out solenoid.
0helpful
1answer

I have a 98 Concorde

You need to check the linkage. Under the car, the section that connects the gear shift stick to the transmission rods.
Not finding what you are looking for?

343 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...