Question about 2000 GMC Savana

Open Question

I have a 2000 GMC 3500 cargo van with a 350,both starter bolts broke at same time. I was able to drill completely thru the outer bolt and thru bolt that one. The other proves to be more of a hassle. I

It's an automatic tranny,1 ton van, with a 350

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
3mac
  • 61 Answers

SOURCE: I want to remove the alternator on my 1986 GMC 2500 Van.

Disconnect and label the wiring harness connections to the alternator (Painters Masking tape works very well for labeling Automotive wiring).

Loosen the alternator pivot bolt.

Remove the bolt that attaches the alternator to the adjustment arm.

Rotate the alternator to loosen the drive belt and disengage the belt from the pulley. Be careful that any spacers that are used in mounting are kept with their original bolts. This will make correct reinstallation much easier.

While supporting the alternator remove the pivot bolt.
Remove the alternator from the vehicle.

To reinstall the alternator, reverse the removal procedure.

Posted on Jan 15, 2009

Ad
  • 2 Answers

SOURCE: how to remove the rear brake pads from 2000 gmc sierra

there are two bolts behind the toward the ends these have to be loosen for the calipers to come off check out auto zone web page for complete instructions

Posted on Jan 27, 2009

  • 73 Answers

SOURCE: Starter Problem

if you drop the trans. dust cover on the bottom of the bell housing you should dee your fly wheel. Place your starter in the position and line up the shims (if needed) . adjust the starter in enough to where it clears the torque converter and shim outward if needed

Posted on Feb 04, 2009

  • 1 Answer

SOURCE: Starter problem on a '92 GMC Sonoma

u have to remove the flywheel housing, then it will drop down

Posted on Jun 23, 2009

  • 335 Answers

SOURCE: 1989 GMC Sierra 3500 loose tilt steering column

Without taking the tilt mechanism off you can only reach 2 of the 3 bolts. If you use 1/4 in. socket on 1/4 in drive with 6 in extension you can just get at the left bolt. If you remove the tilt spring you can get to the bottom bolt. To remoce tilt spring retainer use standard Phillips.

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

We have a cage and can't access the back of the van and now both the rear door and side door are broke. How can we get in the cargo from the outside of the van


Not an easy one if you are meticulous about the condition of your van.

Since you have 2 broken doors already, I suggest either a trip to a good mechanic or a chainsaw.

Oct 09, 2016 | Ford E-Series Van Cars & Trucks

1 Answer

I have a bolt broken off that someone tried to drill out and now i have to find something that will drill through a broken drill bit help?


You can not drill thru a broke drill bit,it is hardened
steel.

Have to try & chip it out first

If you get to a point where you have drilled some & have
a hold on it, heat the spot some & try a short left hand drill bit
to turn it out

They are avail at tool supply stores

Jan 30, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

Removal of starter off a e350 cargo van 7.3 liter diesel year 2000


DISCONECT BATTERY STARTING WITH NEGATIVE
REMOVED WIRES AT STARTER
REMOVED BOLTS HOLDING STARTER TO ENGINE
REPLACE IN REVERSAL

Jul 08, 2011 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

2000 chevy express 3500 van with a 350. Hard time starting. When it starts runs beautiful! Will only start after several taps of the key as if you where setting timing. Not with key fully turning over....


sounds like the check valve in fuel pump is allowing fuel to drain back out of lines. this would require ystem to prime up each time it is cranked. check fuel pressure it should hold with key off if it leaks down this is problem and pump will need to be replaced

Jun 06, 2011 | 2000 Chevrolet Express Cargo

1 Answer

I'm doing front shocks on 1993 ford E250 cargo van and I broke the bottom bolt. Can I brake it off the rest of the way and then drill the bracket through and put a thru bolt or will i have to have a stud...


You can drill it out use a bolt to make a shock mount stud, but make sure the bolt is the correct size for the shock eyelet and you use a lock nut and washers on both sides of the stud you install to replace the old stud, also the new bolt must be a grade 8, anything else will break off very quickly.

Dec 06, 2010 | 2004 Ford Econoline

1 Answer

Where is the starter located on my 2000 chevy


Under your van on the passenger side just above the oil pan on the side of the engine block, bolts into the transmission bell housing, hope this was very helpful.

May 11, 2010 | 2000 Chevrolet Express Cargo

1 Answer

Crankshaft pulley bolt broke. How do i get it out????


You will have to drill the bolt out completely. You could first try an extractor set, it will have to be drilled to the size on the extractor set, use a product called PB Blaster and let it soak for a few days reapplying every 12 hours or so. If it broke off you may not be able to get it out with an extractor set but use the biggest extractor that will fit. If you have the head of the bolt and any threads showing you will have to fid a HSS Drill bit a little smaller than the outer diameter of the threads. then carefully drill the bolt out, it will take forever so take your time, I have set up drills with blocks and bungee cords so it will drill itself without you being in atendance, but the drill has to be positioned precisely as to not damage the inside diameter of the threads for when you install the new bolt. I even went so far at times at home to install a video camera to a small tv inside the house so I could monitor if the drill had changed position. I recently had to do exhaust bolts (6) and a spark plug that had rusted and broken off inside the motor, just the threaded portion of the spark plug was all that was there.

Jan 30, 2009 | 1990 Mitsubishi Montero

2 Answers

Fuel pump for 2001 gmc 3500 box van


The fuel pump is in the tank, there is one for each tank if you have dual tanks, also change the fuel filter with pump.

Nov 06, 2008 | 2001 GMC W3500

Not finding what you are looking for?
2000 GMC Savana Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...