Question about Cars & Trucks

Open Question

Lynx 455 automatic doorman Garage Door Opener lighting

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: remote garage door opener

1-800-355-3515
www.homelink.com

1. Position vehicle within 10 feet of garage door- engine off and battery on.

2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.

3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.

4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.

5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.

6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.

Problems:

1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.

2. Antenna on the garage door opener unit must be hanging down, fully extended.

Posted on Dec 08, 2008

SOURCE: garage door opener 96 LHS

clear the 1-3 buttons on your visor by holding them down until you do not see the blinking light next to it ,after the light shuts off you can take your remote and aim it at the mirror or visor where your 3 buttons are located ,while holding down the button of your garage door opener press the button on you visor/mirror that you want to program it take a few minutes but it can also be programed from the opener smart button ,but you have to get the button in the car to learning mode first , you also can check your owners manual and it will also have information on how to program and also your car dealer can also do it for you when you get your oil changed! i hope i was able to help you and if i was helpful please leave me a nice rating thank you Sincerely glenn mayer

Posted on Mar 07, 2009

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

  • 430 Answers

SOURCE: how to set the automatic garage door opener

This is generally easy. Although you have not mentioned the brand, the system in the car and most cars is made by HOMELINK and they have a great website where you can go to find out how to program almost any car , etc with any garage door opener.

First , since the car is not new, hold button 1 and 3 on the car's overhead console continually for about 30 seconds. The lights will be on solid , then flash, then eventually go out. This erases any old codes. Then select your hanset position and a corresponding position on the cars pad. Lets say button 1. Hold your handheld remote to the overhead console and depress button 1 on both devices while watching the lights flash , fast then slow, then off.
Once done the car has received the signal and is ready to open the door.
On a door system with rolling codes there will also be a learn button ( Chamberlain, Liftmaster. Craftsman, etc.)on the drive unit in the garage,.This button is used to introduce a new device in "SAFE" mode.

Take a step stool , recah up and press the learn button . Then within 30 seconds push the console button in the car for 2 seconds and release. The openers lights will flash to acknowledge, then push the button in the car again for 2 seconds to test. Last step, retest your hand held to be sure it is still active as well. Post back to advise how you made out

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am having trouble linking my Lynx 455 to my Tesla Model S Homelink. Is there a compatibility issue? Does the remote continue to send a signal with the button pressed?


The Model S uses a homelink system for the garage opener, and according to their compability list, the Lynx is not there. So Homelink does not guarantee the functionality of it. If you don't get it to work while following the correct procedures from Tesla, I recommend you get the universal receiver kit from homelink.com Note that there is a difference in transmitter frequency between US and EU universal kits, so make sure you get the correct one. good luck!

Jun 27, 2015 | 2015 Tesla Model S

Tip

2010 BMW 528XI Garage Door Opener Homelink Setup


**** >>> This setup I performed with my new 2010 BMW 528XI Garage Door Homelink and Chamberlain Garage Door Opener <<< ****

Chamberlain:
01. Power off or unplug the garage door opener motor power supply (which is mounted on ceiling of the garage) ;;;

02. keep the garage door opener transmitter in your hand (do not press any button at this time) ;;;

03. In your 2010 BMW 528XI Homelink button (which resides under rear view mirror) press the 1st and 3rd homelink button together for about 30-40 seconds (i.e., until the yellow light blinks fast) and when the yellow light next to the homelink button blinks fast release from pressing the (homelink) buttons ;;;

04. now hold the garage door opener transmitter closer (means within 2-4 inches) to the homelink button (either 1st or 2nd or 3rd) whichever you are planning to program to open the garage door ;;;

05. now press the garage door opener transmitter button and chosen homelink button (either 1st or 2nd or 3rd whatever you need) together ;;;

06. the yellow light (next to homelink button) initially may blink slowly but after few seconds (may be 10-20 seconds) will blink fast; once it started blinking fast release from pressing both garage door opener transmitter and homelink button ;;;

07. Now plug or power on the main garage door opener motor (which is mounted on garage ceiling) ;;;

08. On the main garage door opener motor (which is mounted on garage ceiling) press the "LEARN" button (once you press it may have yellow/orange color light; make sure the light is on) ; then within 30 seconds do the next steps #9, #10, #11 very carefully ;;;

09. go to your car and press the homelink button you programmed and hold it for 4 seconds and then release it --> 1st iteration ;;;

10. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 2nd iteration ;;;

11. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 3rd iteration ** important note; generally three iterations are not necessary; and steps #9, #10, #11 must be performed within 30 seconds ** ;;;

12. during one of the iteration you will hear "CLICK" sound one-time from Garage door motor (which is mounted on ceiling) and if you have light attached with it; it will blink once (** if you hear the CLICK sound and/or light blinks once**) then the particular homelink button is programmed ;;;

13. now press the programmed homelink button; the garage door will open or close (but always it will take 3 or 4 blinks in yellow light or 2-3 seconds before the garage door opens or closes and which is normal) ;;;

** Thats it, your 2010 BMW 528XI Garage Door Opener Homelink setup is complete ** ;;;

You can program rest of the homelink button the same way but following from the steps between #4 and #13 ;;;

Hope this steps will help you to program chamberlain Garage door opener in 2010 BMW 528XI Homelink. ;;;


** possibly the above same steps may work with other BMW 5-series cars homelink too (but I'm not sure) **

on May 29, 2010 | BMW 528 Cars & Trucks

1 Answer

Garage Door Opener


there a botton inside the opener and a botton inside your garage opener push them both at same time it should link together

Dec 11, 2011 | 2002 Oldsmobile Silhouette

1 Answer

Just bought a 2008 Mercury Milan with gargage door opener on the sunvisor. Instructions are not in the manual and want to know how do you reset to open my gargage.


Hold the sync button on the garage door opener located on the roof on the garage. Hold it until the light bulb on the garage dor opener blinks. Hold the remote until the garage door opens or closes. Here is a link to help you out. http://www.ehow.com/how_4614761_program-garage-door-opener-remote.html hope this helps! Please give me 4 thumbs up!

Apr 19, 2011 | 2008 Mercury Milan

1 Answer

Land Rover Discovery 1 1998 garage opener programming


press the two outter buttons for 10 sec. the press the the button on the door remove the same time you hold the button on the door opener. if this still does not work you must push the learn button on the door opener the is attacher to the door. the with in 30 sec push the button in the car thre times

Jul 14, 2009 | 1998 Land Rover Discovery

1 Answer

Homelink garage door opener will only work at very close range - i.e. whent he garage door is open or when the car is in the garage to open to garage door. Is there as RF sensor that could be obscured?


UNPLUG EVERYTHING NEAR THE GARAGE EXCEPT THE OPENER IF THAT HELPS PLUG THEM IN ONE AT A TIME UNTIL YOU FIND THE PROBLEM.
PROBABLY RF COMING FROM SOMETHING IN THE GARAGE, FREEZER, BATTERY CHARGER (IN AN RV OR MOTORCYCLE)
OR A LIGHT TRANSFORMER - EVEN ANOTHER DOOR OPENER CAN CAUSE PROBLEMS - YOU DIDN'T LIST THE BRAND OF OPENER, GENIE HAS REPLACEMENT RECIEVERS IF YOU HAVE MORE THAN ONE UNIT IN A GARAGE.
HOPE THIS HELPS

Jun 07, 2009 | 2002 Lexus ES 300

1 Answer

Programing auto garage door opener


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Apr 18, 2009 | 1999 Oldsmobile Bravada

1 Answer

Program 2004 mercury mountainer garage opener


Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.

Apr 01, 2009 | 2004 Mercury Mountaineer

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

Programming the garage door opener


Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Jun 06, 2008 | 2003 Jaguar XJ-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...