Question about Cars & Trucks

1 Answer

Cant find handbrake adjuster for peugeot 207 - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just fixed mine, the handbrake adjuster is attached to the handbrake lever inside the consul, remove the blanking plastic section to the left of the handbrake, near the driver seat, the with a torch see in side to base of handbrake lever, you will see a vertical rod with a 10mm nut (black) adjustment is done here, quater turn at a time. my problem was the rear 2 cables had falled out of the Tee bar at the back, remove the plastic blanking plate in the rear cup holder see 13mm nut, undo this allows the consol to lift slightly, re insert cables etc, i the tied the 2 cables together with cable tie to stop them popping of the tee bar, so far so good

Posted on Jan 20, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnjohn2
  • 5763 Answers

SOURCE: how do get to and adjust handbrake cable on my 960 volvo

make sure e-brk shoe adjuster is all the way closed. then start adjusting little by little until you can slide disc back on and have a little friction when you spin it by hand, also hope your replacing dics, old one sometime have lots of rust stopping disc from going on anyway good luck and hope this helps.

Posted on Oct 20, 2009

Testimonial: "very fast, thanks "

  • 127 Answers

SOURCE: Break pads on a 207

hallo
remove two bolts from behind
Marko

Posted on Sep 30, 2009

  • 832 Answers

SOURCE: How do you adjust the handbrake on a 1996 Peugeot

Handbrake is normally mechanically connected to
the brakes by steel cable 1/8 inch thick. At the end of the cables are bolts with adjusting nuts to adjust the handbrakes. These nuts must be adjusted to have an equal tension on the brakes, otherwise, swerving may result. It is advised to have a mechanic todo this job.

Posted on Sep 21, 2009

azcoyoterobb
  • 36 Answers

SOURCE: ESP / ARS fault with Peugeot 207

Nobody can give that...at best, a Guesstimate...but they will need to do some testing, Diagnosis...they charge by the hour, are good at what they do, and if they are real good, will be ASE Certified Mechanics...ask around, for good references...I don't know where you live, but in North Portland, (Oregon), there is a small shop on Interstate Ave., that works on them...good luck...

Posted on Jul 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Peugeot 207 rear wheel brake cyclinder replacement


When replacing a Peugeot 207 rear wheel brake cylinder, the Workshop Manual recommends that once the drum has been removed, the brake pipe disconnected from the cyclinder, and the cylinder retaining bolt removed, the upper brake shoe return spring should be removed to allow the cyclinder to be withdrawn from its mounting position.

It is not neccessary to remove the upper brake shoe return spring (tricky to do and even more difficult to put back) - just raise the handbrake (emergency brake) lever a few clicks until the ends of the brake shoes are clear of the cylinder. The cylinder can then be manoeuvred over the upper return spring.

on Apr 13, 2014 | Cars & Trucks

1 Answer

I need the tappet settings for a peugeot 207


inlet valves are set at 0.20mm, exhaust valves are set at 0.40mm, adjust them with the engine cold.

Nov 28, 2013 | Peugeot Cars & Trucks

1 Answer

Tapping noise from engine on peugeot 207 1.4vti 16v on a 08 plate it has done 60000 miles.


On certain makes and models the tapping is an adjustment needed for valves,should be and easy job done by a mechanic familiar with this,good luck

Nov 01, 2013 | 2007 Peugeot 207 1.4

1 Answer

Tapping noise from engine on a peugeot 207 1.4 vti on a 08 plate it has done 60000 miles.


could be valves need adjusted-or a crank bearing going out-cheers Denny

Nov 01, 2013 | 2007 Peugeot 207 1.4

1 Answer

Handbrake adjustment


Don't put It on so hard.

Apr 28, 2013 | 2005 Peugeot 307 1.6

1 Answer

How do u adjust a handbrake cable on a 406


raise and support rear of the car
there is a small metal cover that bolts over the handbrake adjuster

Nov 14, 2009 | 1991 Peugeot 405

3 Answers

Flashing red stop light to dashboard


i have vauxhall vivaro van got starting problems could be glow plugs but now i have a flashing stop light on what looks like a picture of a engine

Oct 25, 2009 | 2006 Peugeot 604

2 Answers

Break pads on a 207


hallo
remove two bolts from behind
Marko

Sep 30, 2009 | Peugeot Cars & Trucks

1 Answer

How do you adjust the handbrake on a 1996 Peugeot 306 XR Hatchback ?


Handbrake is normally mechanically connected to
the brakes by steel cable 1/8 inch thick. At the end of the cables are bolts with adjusting nuts to adjust the handbrakes. These nuts must be adjusted to have an equal tension on the brakes, otherwise, swerving may result. It is advised to have a mechanic todo this job.

Sep 21, 2009 | 1984 Peugeot 604

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,695 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...