Question about Cars & Trucks

1 Answer

1999 Mustang -Washer Motor Not Working. Wiper works as it should when pressing washer button but washer Motor won't run. Checked motor with 12vdc and it runs.

Checked fuse and it was good. Swapped both relays for wiper as they are identical but washer still will not work. Checked power at washer motor connection but no change when pushing washer button.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,251 Answers

Replace wiper switch.Here's the switch.

Posted on Jan 01, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 113 Answers

SOURCE: BMW 740IL Wiper Issue

try checking for a short to power on ur 12 volt comming into motor also check for a good ground at the plug for ur wiper motor

Posted on Jun 17, 2008

  • 102 Answers

SOURCE: 1999 VW Passat. Head lights Blower motor blinkers

yes, it's called the load reduction relay and it is in the 13 fold relay panel under driver side dash.

Posted on Mar 31, 2009

  • 718 Answers

SOURCE: Rear wiper Ford Explorer 1998 won't work.

Look for the fuse for the rear wiper motor is a 15 amp mini-fuse , in location # 8 of your POWER DISTRIBUTION BOX in the engine compartment. Check in the PD BOX for; - relay # 8 is the rear wiper down relay , and - relay # 10 is the rear wiper up relay .

Posted on May 18, 2009

  • 75 Answers

SOURCE: rear wiper motor broke

Well you going to have to open the tailgate up and remove the inside cover that is attached to it. You will need a small flat head and a No. 2 star head screw driver and some gloves so that you don't cut your hands....

First where the handle is remove the caps on the handle and then remove the handle there may be a small pocket around the handle to remove it also with the screw driver....And then remove the garnish from around the tailgate by using the small flat head and your fingers to pry it off with....Remember just to take your time when doing this and wear some safety glasses so that nothing goes in your eyes.

Once you have removed the garnish you should see the wiper motor there should be three bolts that hold it in place and wire wire coupler that it hooked up to it. And before you undo the motor you will need to go on the outside of the tail gate you will need to remove the wiper arm off of the motor and then take the rest off after that.

Posted on May 24, 2009

  • 7353 Answers

SOURCE: Is there an actual fuse for the washer pump, not

Fuse #45, under hood fuel panel.

Posted on Dec 21, 2010

Testimonial: "Thank you. I checked on that myself and this fuse is labeled as the Front, Rear Washer."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

3 Answers

My 2006 Dodge Dakota windshield washer fluid does not spray. I checked the washer pump and it works. The fuses are all good. And the wipers work. When I press the windshield washer button inside the truck...


If the pump works, something should be flowing thru the hose to the spray nozzles.
And if the pump works, everything electrical is working.
How do you know the pump works ?

Apr 14, 2013 | 2006 Dodge Dakota

2 Answers

Ihave a 2003 Ford Explorer & the windshield wipers won't stop working, with the switch turned off or even removed. The only way to stop them is to remove the battery cable.


Sounds like the park switch in the wiper motor is bad.Some manufacturers allwo you to change the circuit board seperately from the motor,sometimes they have to be changed as a unit

Dec 06, 2012 | Ford Explorer Cars & Trucks

2 Answers

My 2001 mustang cobra windshield wipers wont work


Did you ever fix this problem I have a 03 mustang cobra same problem Please help

Feb 05, 2012 | 2001 Ford Mustang

1 Answer

The motor in the washer bottle is not working when i push the button but it's not the fuse and as far as i can tell its no the wiper stem because the wipers work


THE WASHER MOTOR COULD BE BAD IF CHECK TO SEE IF POWER GOING TO WASHER MOTOR IF NO EITHER FUSE BAD OR SWITCH BAD OR HAS A LOOSE WIRE.IF POWER GOING WASHER MOTOR.THE WASHER MOTOR BAD.

Sep 20, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

Winshield wipers dont work


To troubleshoot car windshield wiper problems, you need to thoroughly investigate problems with any of its operating parts. Here are some of the things that you need to check to determine why are your car windshield wipers not working.

Check Wiper Motor
The wiper motor is the driving force of the windshield wiper. Feel the motor and listen to a humming sound. If there is no humming, the motor is the problem. Check if the motor is working properly and see to it that its electrical connections are made properly. If you find that the motor is dead and beyond repair, get it replaced immediately.

Check For Break in Connecting Wires
The connecting wires of the motor sometimes go loose and that may cause the windshield wipers to stop working. Also check the battery plug connection which the motor has. Connecting the loose wires properly or fixing/replacing the plug might solve your problem.

Check Wiper Switch
Another wiper assembly part that can malfunction is the wiper switch itself. Check for switch malfunction and if you find that is indeed the problem, get it replaced from a mechanic.

Check for Bent Wiper Arms
Bent wiper arms can cause the operation of the wipers to be hampered. If the wiper arms are bent beyond repair, get them replaced immediately.

Check For Blown Out Car Fuse
A blown up car fuse could be the culprit that has stopped the windshield wipers from working. Check the fuse assembly under the dashboard of the car. Replacing a blown fuse might fix the problem of windshield wipers not working.

Windshield Wiper Sprayers Not Working - Things to Check

Sometimes the windshield wiper sprayer stops working which can be very annoying. The washer mechanism is a self cleaning mechanism for the windshield. Here are some of the things that you need to check in case it is not working.

Check Windshield Washer Motor
The windshield washer mechanism might have been impaired due to the malfunctioning of the wiper washer motor. Check if its working and get it replaced if it is beyond repair.

Check Windshield Washer Fluid Level
Sometimes the washer doesn't work because the washer fluid levels are not filled to requisite levels. Filling in fluid might restore normal functioning.

Check For Broken Washer Hose
The connecting washer hose that connects the reservoir to the nozzle, might be broken or worn out stalling the overall operation. Check the hose for leaks and get it replaced.

Check Washer Nozzle For Clogging
Last thing to check is the nozzle of the washer for clogging. An obstruction in the washer nozzle might be the reason for windshield wiper sprayers not working. Using a pin, clean the clogged nozzle. This might restore the sprayer to the normal working condition.

Jan 05, 2011 | 1999 Mercury Mystique

2 Answers

Windshield wiper fluid not coming out


remove the hose from the wiper arm and see if when you push the washer button that the fluid comes out the hose,if it does the sprayer nozzel is plugged if not replace the pupm

Dec 02, 2009 | 2001 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...