Question about Nissan Xterra

Open Question

If i disconnect battery cables will that clear my ABS/SLIP/VDC lights

Dissconnect then reconnectting cables on battery clear codes

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: TCS, SLIP and ABS lights on

Check your brake fluid first. If that is low, top it off and recheck. If its ok, than you will need one of the rear ABS sensors. You will need to plug it in and find out which side it is. That's really the only ABS issue that car has. One of the rear ABS sensors fails.

Posted on May 09, 2009

Ad
  • 10 Answers

SOURCE: 2005 Pathfinder - all warning lights on

was toll before disconnect the battery for five seconds and it will clear all the lights codes

Posted on Jul 09, 2009

seanpwright
  • 2030 Answers

SOURCE: Loss of Power, VDC light and Slip light comes on

Have ther codes checked that are making the engine light come on first.

Posted on Sep 15, 2009

  • 105 Answers

SOURCE: ABS, VDC Off, SLIP light all ON

need to read codes for abs system as a fault in abs can cause other codes propbably not a diy job

Posted on Mar 15, 2010

  • 6 Answers

SOURCE: I drive G35X - 'VDC OFF' and ''SLIP" lights are

VDC OFF light will always be off unless you turn it off (this is for traction control). The slip light should not be on however, unless you are driving in rain/snow and the VDC is activated.

Posted on Feb 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 xterra had trans rebuilt VDC light on constant and slip will come on and the go off no codes sowing or ABS?


I know this VDC is commonly due to a steering angle sensor.
You need to use an ABS scan tool and check for the following codes.
C1143 (steering angle sensor circuit)
C1144 (steering angle sensor signal)
C1156 (steering angle sensor com cir)
C1163 (steering angle sensor safe)

Dec 28, 2016 | Cars & Trucks

1 Answer

Replaced damage abs sensor. How do you reset the abs light on a 2000 nissan pathfinder LE?


You will need to clear the codes with an OBD-II scanner, or remove the negative battery cable from the battery for a few minutes. Just be sure the ignition switch is off when disconnecting/reconnecting the battery cable. Have a good one.

May 20, 2015 | 2000 Nissan Pathfinder

1 Answer

How can I be sure if my PCM is bad???


I would try disconnecting battery again. Disconnect both cables and touch them together for a few seconds. This will reset all modules. Wierd that you had so many codes after just disconnecting battery. Sometimes very hard to tell if ecm is bad.

Dec 01, 2014 | 2006 Pontiac Torrent

1 Answer

Replaced battery now check engine light is on


You can delete the codes by removing the battery negative terminal for 5 Sec or more. By this method you can only delete the engine and power train codes. ABS and EPS codes cannot be deleted by this method. Better to retrieve and delete the error codes with code reader or diagnostic computer. Make a note of freeze frame data before clearing the codes.

Jan 09, 2013 | 2000 Toyota ECHO

1 Answer

ABS, VDC Off, SLIP light all ON


need to read codes for abs system as a fault in abs can cause other codes propbably not a diy job

Mar 15, 2010 | 2005 Infiniti G35

2 Answers

350z speedometer stuck at 0 with VDC.TCS/ABS/Slip lights on


check the cable which leads from the tranny to the dash, most of the time the cable or sensor went bad

Sep 23, 2009 | 2003 Nissan 350Z

1 Answer

The engine management light stays on and the abs light stays i have tried everything and they wont turn of my car is a daewoo kalos 2004 make


take the car to a sevice center and have them check for trouble codes which might make the light stay on and tell you what problems the car is having. or disconnect the battery cables and wait 20-30 min then reconnect the cables and see if that clears the codes. usually if a light stays on that means you have problems.

Aug 09, 2009 | 2004 Chevrolet Aveo

1 Answer

No solution yet


VDC/ OFF light is still ON only ? or also SLIP + VDC/OFF ?

if VDC/OFF only u must check ur brake fluid status if both VDC and SLIP u still have problems with ur ABS module and steering wheel


Jun 15, 2009 | 2008 Nissan Xterra

1 Answer

2005 Pathfinder - all warning lights on


was toll before disconnect the battery for five seconds and it will clear all the lights codes

Dec 16, 2008 | 2005 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...