Question about Cars & Trucks

Open Question

How to change rear crankshaft oil sea on a toyota 2RZ engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 132 Answers

SOURCE: 2005 Dodge Stratus with a engine crankshaft code set, after a oil change

The crankshaft sensor has nothing to do with an oil flush. I dont think it could have been hit while draining oil either

Posted on Jan 31, 2009

Ad
  • 4340 Answers

SOURCE: how do you change a rear main oil seal in a 2000 toyota celica gt

First of all, be certain that the leak is in fact from that seal. many leaks travel to that area.

To change the seal is fairly involved, you need to pull the trans and flywheel. There are some specialzed tools involved. Do you have manual or automatic? Manual requires clutch plate alignment on re assembly, by the way , if manual, be sure to change the release bearing and pilot bearing at minimum. Commonly it would make sense to change the clutch during this process....you're already all the way in there..

Posted on Sep 07, 2009

elix0411
  • 3530 Answers

SOURCE: i can't find location of

Welcome to Fixya

There is a housing for the oil filter. Please see procedure below:

1. Jack you car up and place jack stands under the car. Get under the car and remove the bolt to release the oil into a pan. Using the 65mm, 14 flute oil wrench cap, loosen the oil filter housing. This will be pretty tight. Make sure and use a 65mm, not a combination oil wrench cap.
2. Once you have the oil filter housing removed, take out the old filter cartridge and old o-ring, which goes around the end of the oil filter housing. Wipe the oil filter housing clean.
3. Slide the new oil filter cartridge into the housing. Lube the new o-ring with new oil. Slide the o-ring over the housing threads into place. Wipe the engine clean where the filter housing connects. Start to screw the filter housing onto the engine by hand. Once you cannot turn it more, use the ratchet and screw till tight.
4. Replace the drain plug and fill with oil.

Thank you for using Fixya!

Posted on Mar 26, 2011

  • 3 Answers

SOURCE: my 1986 toyota Mr2 has

yes if its in the front but it more like the back one you might just drop the oil pan and do it if you have room to get the iol pan down

Posted on Mar 29, 2011

emissionwiz
  • 76630 Answers

SOURCE: toyota hiace runs too rich, grey/black smoke, petrol engine

Replace the carburetor one of the passage block off plugs was come out. Which one is hard to say.

Posted on Jul 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Oil leak on driveway coming from front of engine


Dear Sir,
Here is the oil leaking Problem Identifying Technique

Engine oil leaks from the valve cover gasket are common.

  • The intake manifold plenum gasket may leak and cause increased oil consumption/burning and a spark knock during acceleration; the gasket should be replaced.
  • External oil leaks from valve cover gaskets, intake gaskets (front or rear), and the rear crankshaft (rear main) seal area are common. The rear main seal is an unlikely source. Normally, the bearing cap mating surfaces (as well as the sealing surface between the oil pan and bearing cap) are the source for the leaks.
  • Engine oil leaks at the distributor can be misdiagnosed as leaks from theintake manifold seal, oil pan gasket, or rear crankshaft (rear main) seal. A revised distributor is available if oil is found inside the distributor.
  • If the oil filter casing shows signs of distortion from excessive oil pressure, theoil pump should be replaced.
  • Often misdiagnosed as a leaking oil filter gasket, the oil filter adapter can seep from between the adapter and engine block.
  • Carbon buildup on the top of the piston is common. As the buildup increases with mileage and over time, symptoms may vary from light ticking, to ticking/hammering, to hammering/knocking noises. Fuel injector cleaner often solves the problem.

  • I think it helps to analyse u r Problem

    Nov 02, 2012 | Toyota Cars & Trucks

    1 Answer

    Oil leaking from toyota camry 1992, 1994 model


    You don't say what engine it has. The 4-cyl was a better than the V6 for oil leaks.

    The V6 had oil leaks from

    -rear bank cam cover gasket

    -distributor o-ring seal

    -oil filter bracket o-ring seal

    -crankshaft nose oil seal (less common)

    -rear main bearing oil seal (expensive, just leave it)

    The 4 cyl leaked oil from

    -distributor o-ring seal

    -camshaft cover gasket

    -rear main bearing seal (expensive, leave it)

    May 21, 2012 | 1991 Toyota Camry

    1 Answer

    I have a huge oil leak in my 98 Toyota Camry It leaks roughly 1 qt of oil for each hour of driving. What would be the cost of repair?


    Need to find out where leak is from. Kinda sounds like a crankshaft main seal, front or rear of engine. Front one is pretty easy to change, but rear main seal leak means you have to drop transmission to get to it. But it could be another seal or gasket. Can you tell about where leak is, from oil spills on ground where parked? Look at engine. Is oil seeming to leak from bottom end or upper engine. May need to wipe or clean it off to see where fresh oil leak develops. A mechanic may need to put it on a car lift to pinpoint the leak. Good luck.

    Oct 24, 2011 | 1998 Toyota Camry

    3 Answers

    Having an oil leak at the bottom of my camry, not the oil pan gasket what else could it be.


    There are three other area's that can leak, here they are in order of how often they occur
    1.Engine Valve cover gasket(s) (2 if V6 engine), oil runs down the engine and drips off the pan.
    2.Rear crankshaft seal leaking
    3.Front crankshaft seal leaking. Oil is blown back by air pressure while driving and rips off of pan.

    Apr 26, 2011 | 1994 Toyota Camry

    1 Answer

    I have a 2006 Pontiac Grand Prix, it is supercharged 3800. I have about 115,000 miles on it and I change the oil every 3,000 miles, check fluids, regular preventative maintenance, etc. I noticed a small...


    If it's oil, it's coming from the rear main seal.. I would go with this idea.

    The seal doesn't cost much but the labor to get to it does.

    To give you an idea what is involved the procedure is illustrated below from the service manual:

    Removal & Installation 3.8L Engine To Remove:
    1. Drain the engine coolant.
    2. Drain the engine oil.
    3. Remove the oil pan.
    4. Remove the engine flywheel.
    5. Remove the rear oil seal housing and gasket. Rear seal removal 3.8L gm-03-38-1175.gif

    6. Remove the rear main seal by placing the housing face down on 2 blocks of wood. Using a drift tool and hammer tap the seal out of the housing.
    To Install:
    NOTE: Do not lubricate the rear main oil seal or the installation tool. Do not touch the sealing lip of the rear main seal once the protective sleeve is removed.
    NOTE: Use a clean lint free cloth to clean the crankshaft sealing surface. Remove sharp edges or burrs that could damage the rear main oil seal. Remove burrs or sharp edges with a crocus cloth.
    1. Carefully remove the rear oil seal from the protective sleeve.
    2. Install the oil seal onto the seal driver EN-47623 or equivalent by placing the seal at an angle and twisting until it is fully seated.
    3. Install the seal into the housing using the seal driver EN-47623 or equivalent and driver handle J-8092 or equivalent. Apply downward force until the seal is seated. NOTE: Ensure that the housing gasket is installed correctly and that the oil passages are not blocked.
    4. Using a new gasket Install the rear oil seal housing on the engine being careful not damage the rear main seal. NOTE: The plastic inserts are used in production and are not needed for assembly.
    5. Hand tighten the bolts. Rear seal housing alignment 3.8L gm-03-38-1176.gif

    6. Place a straight edge on the crankshaft rear oil seal housing flange and the engine block oil pan flange. Using a feeler gauge check that there is no more than .0004 in (0.10 mm) step on each side. Rotate the housing to make the steps equal on both sides.
    7. Tighten the housing bolts 11 ft-lb (15 Nm) plus an additional 50 degrees.
    8. Ensure that the housing did not move out of specification. Repeat step 6 if the oil seal housing is not within the specified range. Replace the rear oil seal housing if the specified measurement can not be reached.
    9. Install the flywheel.
    10. Install the oil pan.
    11. Fill the engine oil and the cooling system.
    12. Check for leaks
    5.3L Engine To Remove:
    1. Remove the flywheel from the crankshaft.
    2. Remove and discard the crankshaft rear oil seal from the rear cover.
    To Install:
    1. Use clean engine oil to lubricate the outside diameter of the crankshaft rear oil seal and rear cover oil seal bore.
    2. Install the tapered cone and bolts of a J 41479 or equivalent crankshaft rear oil seal installer onto the crankshaft.
    3. Place the crankshaft rear oil seal onto the tapered cone.
    4. Install the threaded rod of the J 41479 crankshaft rear oil seal installer into the tapered cone. Rear main seal installer 5.3L gm-03-53-3872.gif

    5. Install the crankshaft rear oil seal by turning the handle of the J 41479 clockwise.
    6. Remove the J 41479 crankshaft rear oil seal installer from the crankshaft.
    7. Install the flywheel onto the crankshaft.
    prev.gif next.gif--- I'm not sure what the exact cost would be as the hours were not listed for this procedure on my online resource.

    Sep 02, 2010 | 2006 Pontiac Grand Prix

    1 Answer

    Leaking oil from the crankshaft seal on a 2001 Toyota Camery 4 cylinder 2.2 liter.


    Ok you have to disassemble the front of the engine, remove time belt, remove crankshaft sprocket, I warn you in these engines often is the oil leak by the seal of the oil pump, so I recommend you change the seal the pump and the camshaft and thus warrant you. Thanks good luck comments

    Jan 30, 2010 | 2001 Toyota Camry

    1 Answer

    My toyota vienta 3VZ-FE 1996 - oil leak onto exhaust


    Hi,

    That engine will leak oil from

    - cam cover gaskets (rear one drips on the exhaust)
    - camshaft end seals
    - distributor shaft o-ring (appears on top of transaxle housing)
    - oil filter bracket to block o-ring seal (drips on front bank exhaust)
    - crankshaft nose oil seal (have done with timing belt change)
    - rear main seal (expensive, leave it be)

    Dec 06, 2009 | 1996 Toyota Camry

    1 Answer

    What is the transmision fluid capacity for 2005 tayota tacoma truck 2 wheel drive 4 cylinder?


    Engine type 2RZ-FE manual trans. API GL-5/75w-90/2.7 qts.
    Engine type 2RZ-FE Auto. trans. Dexron III/2.5 qts.
    Engine type 3RZ-FE manual trans. API GL-5/75w-90/2.6 qts
    Engine type 3RZ-FE Auto. trans. T-IV/2.6 qts
    Engine type 5RZ-FE manual trans. Hypoid API GL-5/75w-90/2.7 qts
    Engine type 5RZ-FE Auto. Trans. T-IV/1.7 qts

    Oct 29, 2009 | Toyota Tacoma Cars & Trucks

    1 Answer

    My 1996 Toyota Camry makes a strange sound whenever I start


    1.check your water pump

    2.check if the engine oil light is offing in time or not,it is like the engiine oil is not being lifted in time by the oil pump,

    3. what should do if is number 1 u have change the water pump and if it is number 2 then change the oil fillter drain the engine oil and replace with new one but this time around add oil treatment oil to the engine oil u change if it is sea 40

    Dec 15, 2008 | 1996 Toyota Camry

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    64 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...