Question about 2002 Toyota Sienna

Open Question

How to replace sensor on 2008 toyota sienna

Obd reading p0051 bank 2 sensor 1

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1201 Answers

SOURCE: 2008 Toyota Sienna Engine knocking

Have the knock sensor checked.

Posted on Jul 22, 2009

Ad
  • 225 Answers

SOURCE: 2004 Toyota Sienna code P0430, Catalyst system

7 out of 10 times that means that one of the cat's have gone bad. Most of the time it happens when your mileage is around 100,000 miles. The only thing is to do is to change the bad cat.

Posted on Aug 30, 2009

  • 291 Answers

SOURCE: the check engine light is on the code is P0051

FIRST THING IS RESET THE CHECK ENGINE LIGHT AND SEE IF CODE RETURNS... RUN IT FOR A LITTLE TO MAKE SURE YOU DON'T HAVE BAD GAS.... IF IT STILL COMES ON REPLACE 02 SENSOR LOCATED IN THE EXHUAST PIPE.. THERE SHOULD BE TWO IN PIPE YOU WANT THE ONE CLOSEST TO THE END OF THE EXHUAST PIPE

Posted on Sep 01, 2009

  • 114 Answers

SOURCE: i can't find knock sensor location bunk 2 toyota sienna 2001

It's under the intake manifold...oh joy

Posted on Sep 19, 2009

Testimonial: "you are a nice guy. i'm so gratefull you have this in the networth. thanks."

crapiemael
  • 241 Answers

SOURCE: p0051 code, where is the sensor located, where is

Bank 2 is passenger side, sensor 1 is the one up closest to the exhaust manifold. Plug in type (just remove old and plug back into the wiring harness connector) is about $90 at Autozone. You can get a cheaper one that you splice but it's confusing to understand which wires to splice together. Don't forget to buy the special socket, $10, to remove and install the sensor. It's split up the side for the wires. Forget trying to use an open end wrench, socket is best.

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have Toyota Sienna 2001 SE and code 1150 came it's showing on obd|| bank2 sensor1.i don't know where is located plz help


hello, the banks 2 sensor is located in the exhaust manifold near the firewall and visible from the top, you will need a special o2 sensor socket to remove it.

Apr 03, 2017 | Toyota Cars & Trucks

1 Answer

We have fault codes#1 and #51 and we need to know what they mean can anyone help


Ian, P0001 fuel volume regulator control circuit/open, may be an electrical problem related to the fuel volume regulator. clear the code and see if it comes back
P0051 Oxygen sensor heater control circuit low, bank 2, sensor 1.
Normally a bad wire/plug on sensor or sensor faulty.
Check the attached links,instruction and guides to explain codes in more detail. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.obd-codes.com/p0051
http://www.obd-codes.com/p0001
P0001 OBD II Trouble Code Fuel Volume Regulator Control Circuit Open

Apr 26, 2016 | Cars & Trucks

1 Answer

What should I check with 3 codes P0051 , P0300, P1512 .its only car I have and I need expert advice what's smartest cheapest thing to do?


the following link is courtesy of obd codes .com the p0300 misfire code can be from the other to codes P0051 - Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) OBD-II Trouble Code Technical Description Generic: Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) Nissan: Heated oxygen sensor (HO2S) 1 Bank 2 - heater voltage low What does that mean? A P0051 DTC (diagnostic trouble code) refers to the O2 sensor (oxygen sensor) located on Bank 2 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2. This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. It detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle's computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the A/F O2 sensor. Essentially this P0051 code means that the resistance of the heater circuit is lower than normal. In most cases, that resistance level must fall below 0.8 A to trigger the DTC code. Note, this code is very similar in nature to P0031, P0032, and P0052 Potential Symptoms Most likely you'll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate. Causes A P0051 DTC trouble code may be caused by one or more of the following: A short in the heater circuit in the sensor A failed O2 sensor heater Wiring/connectors broken/frayed leading to sensor and/or relay Failed PCM/ECM Possible Solutions To fix a P0051 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to: check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement) check the ground circuit for continuity measure the resistance of the heater circuit (done on the sensor itself) measure the resistance and voltage of the wiring Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is below 0.8 A. With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #1 on bank 2 (the side of the engine that doesn't contain cylinder #1). Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0051 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).

Read more at: http://www.obd-codes.com/p0051
Copyright OBD-Codes.com OBD Codes Your OBD-II Trouble Codes Repair Site Home Trouble Codes FAQs Forums Store P0300 Diagnostic Code - Random Misfire Technical Description Random/Multiple Cylinder Misfire Detected What does that mean? Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly. A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why. Symptoms Symptoms may include: the engine may be harder to start the engine may stumble / stumble, and/or hesitate other symptoms may also be present Causes A code P0300 may mean that one or more of the following has happened: Faulty spark plugs or wires Faulty coil (pack) Faulty oxygen sensor(s) Faulty fuel injector(s) Burned exhaust valve Faulty catalytic converter(s) Stuck/blocked/leaking EGR valve / passages Faulty camshaft position sensor Defective computer Possible Solutions If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back. If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors. Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open. It is helpful to have access to a factory service manual and an advanced scan tool to properly diagnose a random misfire DTC. P0300 Diagnostics Video Here is a helpful video that may assist you in learning more, diagnosing, and repairing your P0300 DTC. This video is intended for auto repair professionals but could be helpful to DIYers. It shows use of an advanced OBD-II scan tool during diagnostic steps:

Read more at: http://www.obd-codes.com/p0300
Copyright OBD-Codes.com
http://www.obd-codes.com/search/?cx=006282753923640923292%3Absyyn-_1vle&cof=FORID%3A11&ie=UTF-8&q=p1512&sa=Search&siteurl=www.obd-codes.com%2F&ref=&ss=1863j1029425j5 Engine-Codes OBDII Code List P1512 Mazda
P1512 Mazda P1512 Mazda - Variable Tumble Control Solenoid Stuck Closed 0 ' Add Comment Possible causes
- Variable Tumble Control Solenoid (VTCS) vacuum solenoid stuck closed
- Faulty Variable Tumble Control Solenoid (VTCS)
- Variable Tumble Control Solenoid (VTCS) harness is open or shorted
- Variable Tumble Control Solenoid (VTCS) circuit poor electrical connection
What does this mean? When is the code detected?
Variable Tumble Control Solenoid (VTCS) Dual Plane Intake system
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Read more: http://engine-codes.com/p1512_mazda.html#ixzz3ihjeps00

Aug 13, 2015 | 2000 Mazda MPV

1 Answer

Can an O2 oxygen sensor effect another sensor and give a false reading?


Check which side of your engine has cylinder #1. That side is bank 1. Bank 2 is the side opposite of bank 1. So bank 2 is not always passenger side. And since you seem to have extra O2 sensors, I would replace the other upstream and see what happens. Also the mass air sensor can give a trouble code issue to the upstream 02 sensors. Good luck. I've struggled thru this myself.

Mar 06, 2015 | Cars & Trucks

1 Answer

2007 Toyota sienna V6 P2197 code from Autozone diagnostic.


Solved. I have 2008 Sienna with Check Engine and VSC lights on. Scanned codes were P0051 and P2197. Oxygen Sensor Bank 2 Sensor 1 needs to be replaced. You can see this sensor on the right side of the engine when you open up the hood. You need to get an Oxygen Sensor socket (I used Tekton 7/8in 22mm which costs $9) and a wrench extension to reach it. Spraying liquid wrench a few times on the base of the old sensor also helped to loose it. The replacement sensor I used was Denso 234-9049 which costs $85 from eBay. Lights went off after the sensor was replaced. It took me 30 minutes to replace.
2007-toyota-sienna-v6-p2197-code-from-l0sykieabygz51ktlgs3lp2u-4-0.jpg

2007-toyota-sienna-v6-p2197-code-from-l0sykieabygz51ktlgs3lp2u-4-1.jpg

2007-toyota-sienna-v6-p2197-code-from-l0sykieabygz51ktlgs3lp2u-4-3.jpg

2007-toyota-sienna-v6-p2197-code-from-l0sykieabygz51ktlgs3lp2u-4-6.jpg

2007-toyota-sienna-v6-p2197-code-from-l0sykieabygz51ktlgs3lp2u-4-10.jpg

Sep 07, 2012 | 2008 Toyota Sienna

1 Answer

Where is location knock sensor 2002 toyota sienna


Go to the link and scroll down the page to the knock sensor replacement procedure. It is very involved and if you don't know car repair leave it alone, There are 2 sensors, on for each cylinder bank.

How to fix your Toyota Sienna Knock Sensor Malfunction P0330 P0335without...

Mar 21, 2012 | 2001 Toyota Sienna

1 Answer

Which senser needs replacing with code p0051


A P0051 DTC (diagnostic trouble code) refers to the O2 sensor (oxygen sensor) located on Bank 2 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2.

This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. It detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle's computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the A/F O2 sensor. Essentially this P0051 code means that the resistance of the heater circuit is lower than normal. In most cases, that resistance level must fall below 0.8 A to trigger the DTC code.

Potential Symptoms Most likely you'll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.
Causes A P0051 DTC trouble code may be caused by one or more of the following:
  • A short in the heater circuit in the sensor
  • A failed O2 sensor heater
  • Wiring/connectors broken/frayed leading to sensor and/or relay
  • Failed PCM/ECM
Possible Solutions To fix a P0051 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to:
  • check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement)
  • check the ground circuit for continuity
  • measure the resistance of the heater circuit (done on the sensor itself)
  • measure the resistance and voltage of the wiring
Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is below 0.8 A.
With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #1 on bank
2 (the side of the engine that doesn't contain cylinder #1).

Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0051 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 05, 2011 | Toyota Sequoia Cars & Trucks

2 Answers

Where is bank 1 sensor 2 oxygen sensor located?


The bank 1 sensor 2 sensors are always oxygen sensor located behind the cat converters, the A/F ratio sensors are always in front of the cat in the exhaust manifold, the part number for the sensor B1/S2 is 89465-09290 from Toyota. Thanks.Helpmech.


Nov 12, 2010 | 2002 Toyota Sienna

Not finding what you are looking for?
2002 Toyota Sienna Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...