Question about 2000 Isuzu Rodeo

Open Question

Torque specs 02 rodeo thermostat housing - 2000 Isuzu Rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

Ad
mx5turbo92
  • 545 Answers

SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009

germcelchar
  • 389 Answers

SOURCE: 1995 isuzu rodeo front wheel bearing torque specs.

To adjust wheel bearing torque. Tighten the nut fully until the wheel wont turn then unscrew slightly until the wheel turns freely. Replace the locking plate and its set.

Posted on Nov 17, 2009

carsandcomps
  • 722 Answers

SOURCE: need torque specs for isuzu rodeo 3.2 intake

josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Posted on Apr 10, 2010

iambanshee74
  • 3489 Answers

SOURCE: torque specs for 3.2 1995 heads on isuzu rodeo

0900c152800622a3.gif

To install:

  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

Posted on May 16, 2011

Testimonial: "Very detailed and exactly what I needed.....THANKS"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1995 ford windstar thermostat housing bolt torque spec


Most people don't bother using a torque wrench to tighten a thermostat housing.

It is more important to be careful and tighten each bolt a little at a time. You do not want to warp, crack, miss align the part you are bolting.

It does not take a lot of torque to seal a thermostat housing. I would guess somewhere between 15 and 20 ft lbs.

It is often hard to find such torque specs for specific vehicles.

For bolts that you cannot find a specified torque spec, you can refer to a standard bolt torque chart. The charts are based on the diameter of the bolt threads not the wrench size used to fit the bolt head. The charts also depend on the hardness of the bolt material. Also keep in mind the material you are bolting into.

Here is one such chart...
http://www.dansmc.com/torque_chart.htm

Keep in mind that thermostat housing bolts are just sealing a gasket. They are not holding the entire car together.

After turning wrenches for many years, most mechanics just know by feel.

There are cases where a torque wrench is mandatory. Like head bolts, wheel bearing/hub nuts, rod caps, main bearing, etc.

Jul 16, 2014 | Ford Windstar Cars & Trucks

1 Answer

What are the torque specs for a 2003 Chevrolet trailblazer thermostat housing?


The 2003 Chevrolet Vortec 5300 generated 285 horsepower at 5,200 rpm and 325 ft.-lbs. of torque at 4,000 rpm. --------------------------------------------------------------
VVDI VAG Vehicle Diagnostic

Mar 26, 2013 | Cars & Trucks

1 Answer

02 rodeo is leaking water from on top of the manifold


I have a '98 rodeo and had a similar problem. I had to remove the manifold to get to the thermostat housing. A rigid coolant line is connected to the thermostat housing on the aft side of the housing. That rigid line is sealed with a little o-ring that had deteriorated. A lot of work for a small o-ring.

Dec 20, 2012 | 1998 Isuzu Rodeo

1 Answer

What is the torque spec for the thermostat housing


THERMOSTAT HOUSING BOLT TORQUE IS 15 - 22 FT LBS.

Jul 11, 2010 | 1998 Lincoln Town Car

1 Answer

What is torque spec for 2004 Ford 4.0 thermostat cover bolts? Replaced black ''plastic'' thermostat housing and inlet cover. Thanks


Normally these bolts are about 20-24ft lbs. You don't want to over tighten them as they should have a rubber washer/gasket to help provide a good seal. These cast aluminum housing will easily strip so just use care when tightening. Just snug both bolts and run the vehicle til it reaches operating temp then check for leaks. You can also purchase a Chiltons/Haynes manual for your vehicle at any auto parts store for $15 they normally give you the torque specs as well as some other valuable tipe

Aug 06, 2009 | 2004 Mercury Mountaineer

1 Answer

Torque specs


Hello mikemcgee63, my name is JShreader. Thank you for choosing fixya.com.

The Torque Specs for the Thermostat Housing are 10 Nm (89 inch lbs.).

I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 30, 2009 | 2001 Chevrolet Corvette

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...