Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The coolant level sensor is located on the radiator. If you are looking at the engine from the front of the car it will be on the left side. There will some kind of clip holding it in the radiator. Removed the clip and pull the sensor out. You will lose coolant so try to swap it out quick or drain some of the coolant out. Once new sensor is installed, install clip to keep the sensor in place and reconnect the wires to the sensor. Crank the engine and make sure the coolant level is full. This should correct your problem.
Posted on Jan 04, 2009
SOURCE: replace coolant level sensor
THESE SENSORS ARE A KNOWN PROBLEM REPLACE IT, IT IS HELD IN BY A WIRE RETAINER CLIP, IT IS LOCATED IN THE PLASTIC SIDE TANK OF THE RADIATOR NEAR THE TOP OF THE TANK, ENGINE SIDE. THE PART IS ABOUT $60.00
Posted on Jul 17, 2009
Usually mounted to the radiator into one of the coolant tanks,about 1/3 of the way down the radiator with a wire harness a weathertite connector. Good luck !
Posted on Nov 29, 2009
Tips for a great answer:
May 18, 2015 | 2000 Mercury Mountaineer
Jul 23, 2012 | 1991 Chevrolet Caprice
May 20, 2010 | 2002 Suzuki XL-7
Nov 26, 2009 | 1996 Chevrolet Caprice Classic
There is a TSB for this problem. Here it is.
Bulletin No.: 04-06-02-007
Date: August 11, 2004
Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)
2000-2002 Buick Century, Regal
2000-2001 Chevrolet Lumina
2000-2002 Chevrolet Impala, Monte Carlo
2000-2002 Pontiac Grand Prix
2000-2002 Oldsmobile Intrigue
Some customers may comment that the low engine coolant level
indicator is always illuminated.
The cause of this condition may be due to engine oil
contaminating the coolant. Possible sources of oil contamination are internal
engine leaks, improper service procedures, or the addition of some types of
anti-leak additives to the cooling system. Once in the coolant, the oil leaves
deposits on the level sensor creating an insulating film. This film results in
a false activation of the coolant level indicator.
Diagnose low coolant level system operation and check the sensor
for oil contamination using the procedure listed below.
Important: No coolant supplements should be used in GM cooling
systems, other than what is approved and recommended by GM. The use of
"aftermarket" over-the-counter sealing and cooling supplements may
affect the operation of the low coolant level sensor. Discoloration of the
coolant recovery bottle is normal and does not necessarily indicate that
coolant contamination is present. Flush cooling system only when instructed by
Verify that the coolant is at proper level in the radiator and
the coolant recovery bottle. If the coolant is low, add proper amount of 50/50
water and DEX-COOL(R) mixture. If the low coolant light operates properly,
diagnose the cooling system for loss of coolant as outlined in SI. DO NOT
proceed further with this bulletin.
2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section.
3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light:
^ Light is on - Chassis wiring or instrument cluster concern.
Follow the appropriate diagnostic information in SI.
^ Light is out - Proceed to Step 4.
4. With the key off, connect the coolant level sensor into the vehicle's wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds.
^ Light is on - Replace the low coolant sensor and re-check
^ Light is out - Proceed to Step 5.
5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Re-install the low coolant sensor into the vehicle and proceed to Step 6.
6. Flush the cooling system and install new DEX-COOL(R) mixture as outlined in the SI. Check the vehicle's warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination.
Oct 31, 2009 | 2002 Chevrolet Monte Carlo
Aug 26, 2009 | 1995 Chevrolet Caprice
Aug 18, 2009 | 1991 Chevrolet Caprice
Nov 23, 2017 | Cars & Trucks
31 people viewed this question
Usually answered in minutes!