Question about Cars & Trucks
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: transmission code
Here is the TSB from Ford:
Here it is... TSB 03-22-10...
FORD: 1995-2001 EXPLORER
2000-2002 EXPLORER SPORT
2001-2002 EXPLORER SPORT TRAC
MERCURY: 1997-2001 MOUNTAINEER
This article supersedes TSB's 03-11-9, 02-13-8 and 02-08-2 to update the model coverage.
Some vehicles built prior to 12/1/2001 may exhibit the following shift and engagement conditions:
No 2nd Gear
No 3rd Gear
No Engine Braking In Manual 1st.
Out of specification pressures controlled by the transmission main control valve body separator plate may be the cause.
Verify the condition, the main control valve body separator plate may need to be updated to the latest level. Refer to the following Service Procedure for details.
CAUTION: A NEW SEPARATOR 7Z490 MUST BE USED WHEN INSTALLING THE SPECIAL SERVICE KIT 7M203 OR ADDITIONAL TRANSMISSION DAMAGE MAY OCCUR. REFER TO THE PARTS APPLICATION CHART IN THIS ARTICLE FOR CORRECT SEPARATOR PLATE PART LISTING.
NOTE: THIS ARTICLE DOES NOT APPLY TO ANY OTHER CONDITIONS OR COMPONENTS THAT MAY CAUSE SIMILAR SYMPTOMS AND IS ONLY WRITTEN TO COVER THESE SPECIFIC CONDITIONS.
NOTE: AN IN-LINE SERVICE FILTER IS NOT REQUIRED TO BE ADDED OR REPLACED FOR THIS TSB.
Verify that one or more of the following conditions exist.
Low Line Pressure While In Drive At WOT
No 2nd And/Or No 3rd Gear
No Engine Braking In Manual 1st
DTC P0732, P0733 Or P1762
Install Kit (3L5Z-7M203-JA) to update the main control valve body assembly, refer to the installation procedures found in the kit.
Reinstall the main control by continuing to follow the installation steps listed in the Workshop Manual, in-vehicle service, main control valve body.
After completing the procedure, verify the condition has been corrected.
Clear all DTCs.
Part Application Chart
Vehicle Application Engineering Description Qty. New Service Part Use on Transmission Application 7000 -Reference Only-
95/96 Models ONLY
95/97 Models Separator Plate to Case Gasket 1 2L5Z-7C155-AA ALL
95/97 Models Separator Plate to Main Control Gasket 1 2L5Z-7D100-BA ALL
95/96 Models - ALL Plate - Valve Body Separator 1 F5TZ-7A008-CA 95GT-AA/BA/CA/DA/EA/FA/ GA;96GT-BA/CADB/EB/FA/ GA/HA/KA/MA/NA
97 Models ONLY
97 2.3L Ranger Plate - Valve Body Separator 1 F77Z-7A008-AB 97GT-GC
97 3.0L OHV Ranger/Aerostar Plate - Valve Body Separator 1 F77Z-7A008-AB 97GT-EC/FC/MC/NC/RE/SE
97 4.0L OHV Ranger/Aerostar Plate - Valve Body Separator 1 F77Z-7A008-CB 97GT-KE/LE
97 4.0L OHV Explorer/Mountaineer Plate - Valve Body Separator 1 F77Z-7A008-DB 97GT-KF/LF
97 4.0L SOHC Explorer/Mountaineer Plate - Valve Body Separator 1 F77Z-7A008-EB 97GT-AE/BE
1998-2001 Models ONLY
98/01 2.5L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-DA 98GT-GA; XL5P-CA
98/00 3.0L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-EA 98GT-EB/FB; XL5P-AA/BA
98/00 4.0L - EI Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-FA 98GT-KB/LB; XL5P-DA/EA/FA
98/00 4.0L - EI Explorer Plate - Valve Body Separator 1 1L5Z-7Z490-GA 98GT-CB/DB; XL2P- EA/FA
98/00 4.0L - SOHC Plate - Valve Body Separator 1 1L5Z-7Z490-HA 98GT-AA/BA; XL2P- CA/DA
2001-2002 Models ONLY
2001/2002 2.3L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-AA 1L5P-CA
2001/2002 3.0L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-BA 1L5P-AA/BA
2001/2002 4.0L-SOHC - ALL Plate - Valve Body Separator 1 1L5Z-7Z490-CA 1L5P-DA/EA
1995-2002 ALL as Listed Above Valve Body Service Kit 1 3L5Z-7M203-JA ALL
Posted on Jun 11, 2008
P1400 on your vehicle is described as :Differential Pressure Feedback EGR Circuit Low Input You either need a new DPFE valve, or a new EGR valve. Both can be tested for functionality before replacing them both. EGR valve is more likely I think. Cleaning it may not improve its performance, but its worth a try. Also check the vacuum lines between the DPFE and EGR system. The EGR valve and DPFE are usually close together above the exhaust manifold/downpipe. you need service instructions to test these items, suggest you go to a garage really...
Posted on May 17, 2009
Any shop should be able to get that price for you. Service the trans and filter while its apart. Est $200.00
Posted on Nov 13, 2009
bank 1 sensor 2 is the left downstream sensor (1/2) is located in the exhaust downpipe just after the mini-catalytic convertor, and before the main catalytic convertor. Now the meaning of this is that your not getting any 12+/12- heating on sensor, which means voltage is supplied to heat sensor up. You have a O2 sensor heater relay, but not getting problem with 2/2 sensor tells me you need to check/inspect the wiring for 1/2 sensor, open wiring for 1/2 sensor and inspect
Posted on Feb 07, 2010
EVAP fuel tank pressure sensor low output. It sounds like the charcoal -filled canister, it's near the gas tank in a cylinder shape.The canister may have cracks or a hose is leaking around the area and it will give a fault code of PO452. Are you smelling any odors or emission smell from the car?
Posted on Feb 26, 2010
Tips for a great answer:
Sep 26, 2014 | 2009 Hyundai Sonata
Jan 18, 2013 | Cars & Trucks
Jan 13, 2011 | 2001 Hyundai Elantra
Sep 27, 2010 | 2000 Nissan Maxima
Apr 06, 2010 | 1997 Chevrolet S-10 Pickup
Feb 07, 2010 | 2001 Dodge Durango
Oct 03, 2009 | 2000 Saturn SL
May 05, 2009 | 1998 Ford Expedition
Apr 29, 2009 | Chevrolet Monte Carlo Cars & Trucks
Jan 17, 2018 | Lincoln Cars & Trucks
Jan 17, 2018 | Cars & Trucks
27 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: