Question about 2005 Jeep Liberty

1 Answer

05 jeep liberty changing spark plugs

Is there any tricks or hints i should know about going in?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 217 Answers

3.7L pretty straight and easy, but should change wires also

Posted on Jan 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Trying to install replacement side passenger window in Holden Berlina 2002 VX II - not having much luck - any hints/tricks?

what exactly are you having trouble with? the fitting of the glass? removal of the trim to gain access?

Sep 13, 2016 | Holden Cars & Trucks

1 Answer

Auto trans shifts into reverce but not drive

or or cold engine? or both./
did you check the TCM brain for scan codes
this year, is either the jumper and bulb flash trick
or use any real OBD2 (USA?)_ scan tool to see all scan DTC codes
P07xx car trans. covers this, why not log in and look.

1: check all fuse
2: check trans levels using oper. guide method , hint dont guess.
3: run scanner, (or flash code checks on TCM)
4: do the 50k mile full fush and filter change now, if not too late.
lots more, tell more get more.

Jan 31, 2014 | 1998 Toyota Celica

1 Answer

I need to change the main bearing and seals in the engine. Is this an easy job? Are there any special hints /tricks I should know about?

no tricks about it. get a crank kit with the bearings to do this right or your wasting your time and money
A shop manual sold at auto parts stores is a great investment to have also

Apr 17, 2011 | 1995 Suzuki Swift

1 Answer

Looking for guide on how to replace front fender

I have a TDI but would think its the same setup. Remove the 4 star nutted screws from wheel arch shroud on both sides. Looking at the front of the VW where the towing eye facia is remove this and undo the 10mm bolt same for the other facia on the opposite side. Then the final 2 bolts are under the headlights. hope this helps

Feb 17, 2010 | 2002 Volkswagen GTI

2 Answers

My 2003 Ford explorer has a Ford remote starter and it

no take it 2 dealer ask a mechanic if theres a trick or does it need to be re proged

Jan 13, 2010 | 2003 Ford Explorer

1 Answer

Tips hints or tricks and detailed instructions for getting front drive shaft on spindle coming from transmission. Do i put the clip on the spindle coming from tranny or does it goes inside the shaft tht...

no its goes on the shaft that comes out of trans,,put the opening on the clip facing up,for some reason its seems to go on alot easier with the clip up,,,,wiggle it on and make sure its straight then push really hard and get it to seat al the way on,if its not all the way it will pop off while driving,then youll have to get a tow,so make sure its seated all the way

Oct 16, 2009 | 2002 Saturn VUE

1 Answer

Need to change the egr valve. It is very hard to get a wrench on it. Do you have any helpfull hints

are you sure its bad?, its rare that it is. when you apply vacuum to it, the engine should idle rough or stall. if it doenst make any difference, it may be bad or stuck or the passages could be plugged and you can clean them out. sorry tricks

Oct 14, 2009 | 2000 Mercury Cougar

2 Answers

A/C works but air coming out is not as cold as it used to be

this car uses r134 freon you can get a can with a pressure guage on it for about $14 dollars and do it yourself just don't overfill it. find the a/c lines you will have two fittings one is bigger than the other the big one is the high side the small one is the low side this the side you want to charge it on make sure vehicle is running when you do this it sucks the freon in easier when you have it on and set a max a/c.

Aug 28, 2009 | 1999 Lexus RX 300

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides