Question about Mitsubishi Cargo

Open Question

2005 Mitsubishi Express L300 workshop manual - Cargo Mitsubishi Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
swoop611
  • 488 Answers

SOURCE: I need a workshop manual

The mixture screw is located in a resessed hole just above the therma start plate at the rear of the carby. The rear of the carby faces away from the inlet manifold and you require a special tool to access this adjustment. The other screw adjustments on the carby and linkages are for idle, fast idle, and choke limits including those models with automatic (thermal type) choke mechanisms.
I would advise that if you make any adjustments to the mixture that you have the mixture checked using an exhaust gas analyser.However, as a general rule of thumb, screw the mixture adjustment all the way in until you feel it tighten but DO NOT FORCE IT !! the screw has a delicate needle valve on the end which will be damaged if the screw is forced beyond it's normal length of travel.
Unscrew the mixture screw a total of one and a quarter turns back out and then have the setting checked with a exhaust gas analyser. Too rich and not only is this expensive but will cause damage to spark plugs etc. Too lean a setting will cause a misfire which will damage valves and pistons.

Posted on Mar 08, 2011

Ad
emissionwiz
  • 78272 Answers

SOURCE: workshop manual Mitsubishi FK115

I am sorry but fixya has no factory repair manuals.

Posted on Aug 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i download a workshop manual for a 2005 MITSUBISHI EXPRESS VAN?


try this forum http://www.mitsubishi-forums.com/70-l300-l400-delica-exceed-starwagon-forum/56290-l300-repair-manual-4x4.html

Dec 08, 2017 | Mitsubishi Cars & Trucks

Tip

Indicator fuse blow Mitsubishi L300 wagon


Fuse blowing on Mitsubishi L300 2.4l motor, manual gearbox. Fuse 15, indicators, fuel guage, tacho. Found to be short in reversing light switch in gearbox. Initial disconnect of switch stopped fuse blowing, renew switch restored reverse lights

on May 29, 2014 | Cars & Trucks

1 Answer

Inner and outer tie rod torque specs for 2005 chevrolet express 3500 extended van


Hello Dale,

Please follow the links below for the information you have requested. I would like to make this easy for you but I have no idea which 2005 Express you're referring to...so you can follow the link below to isolate your particular model.

Chevrolet Workshop Manuals


Here is another link that provides 236 pages in PDF format on the 2005 Express.

https://www.gmheritagecenter.com/docs/gm-heritage-archive/vehicle-information-kits/Express-Van/2005-Chevrolet-Express-Van.pdf

Apr 18, 2017 | Chevrolet Cars & Trucks

1 Answer

I have a mitsubishi l300 with a 4G64 engine I have just replaced main bearings it ran ok but now it's blowing smoke. Compression is ok but all the plugs are dry black as if it's getting too much fuel


F]ENGINE Workshop Manual 4G6 (EW) - mmc@mitsubishi-motors.kiev.ua

mitsubishi-motors.kiev.ua/Manuals/Engine/pwee9616/11A.pdf

you have to run it in and wait and see
you may burn up a set of plugs

renew main bearings only raise the conrods and pistons
so piston and rings will run in a different position up the cylinder wall

only doing mains and not conrods and re-ring is a strange thing to do

Apr 16, 2017 | Mitsubishi Cars & Trucks

1 Answer

How do i tune a 1988 Mitsubishi express van l300


Install new spark plugs, new spark plug wires if needed, a new gas filter, a new air filter if needed.

Jun 25, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where's the computer in an Mitsubishi 1993 L300 express van?


my guess is the pillar behind the drivers head behind the plastic covering.

May 21, 2015 | Mitsubishi Cars & Trucks

2 Answers

How to toque head bolts on a 2005 mitsubishi galant engine


No question, Get a manual with the correct tightening sequence and tourque settings. This can go very bad very quick if done incorrectly!! manuals are cheap at most auto parts stores.

Nov 26, 2014 | 2005 Mitsubishi Galant

1 Answer

Heater wont blow hot air in van. How do i fix it?


add coolant to the radiator and it should help circulate it and warm the air up

May 07, 2009 | Mitsubishi Minivan Cars & Trucks

1 Answer

L300 express van/ starter motor


http://www.alldatadiy.com will cover your vehicle completely. However, there is a subscription fee; $21 for the first vehicle and $16 for each additional vehicle for a year subscription. Or, you could send a text from your cell phone to Cha Cha, (242-242) and ask them. It is free and only costs whatever it normally costs you to send a text from your cell phone. They can answer ANY question. Real people. Not computers like Google.

Aug 19, 2008 | 1990 Mitsubishi Minivan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...