Question about 2004 Isuzu Rodeo S 3.5L V6

Open Question

Where is the map sensor p0106 located on a isuzu rodeo 3.5 engine S

Where is the map sensor p0106 located on a isuzu rodeo 3.5 engine 4 wheel drive

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CRTN
  • 716 Answers

SOURCE: 98 isuzu rodeo 4wheel drive wont egage light on dash blinking

is it because your not at a stop?

Posted on Jan 05, 2009

  • 13 Answers

SOURCE: 4 wjheel drive problem

not transfer case motor....there is none on a rodeo....trooper has torque on demand.....rodeo problem is likely shift on fly mtr...mounted on front axle....if u dont use 4wd regularly it sticks and gets stuck.

Posted on Feb 15, 2009

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

  • 75 Answers

SOURCE: where is the map sensor located on a 2004 rodeo

check the right side of the intake manifold or the right rear of the intake manifold...

Posted on Feb 03, 2010

  • 14 Answers

SOURCE: 2001 Isuzu Rodeo 4 cyl 2.2L 2WD that is overheating

check the electric fan conector plug some times is rusti scratchet whit a sharp scruwdriver remove the rusti or dirt on it this happens many times and step two check the relay and thats it (this is the first step a mecanic to search)

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Spark plug firing order


Hello Harvey, My information shows firing order of 123456. #1 being passenger's front cylinder and #2 being driver's front cylinder.

Jul 30, 2014 | 1995 Isuzu Rodeo

1 Answer

My check 4 wheel drive light stays on and will not engage into 4 wheel drive on my 2005 rodeo


With ignition key turned on ,but engine not running, press all 3, 4wd buttons at the same time and hold on for 20 secs. This resets the computer. This same application applies if you are locked in 4x4 and it wont release back to 2wd.

Aug 25, 2012 | 2004 Isuzu Rodeo

2 Answers

Where is the map sensor located on a 2004 isuzu rodeo 3.5l v6


check the right side of the intake manifold or the rear of the manifold

Mar 04, 2011 | 2004 Isuzu Rodeo

2 Answers

I have a 2004 Isuzu Axiom, my check engine light came on as i was on the interstate with my cruise control on. The cruise control stop working exactly the same time the engine light came on. I took it to...


You may have actually had a faulty MAP that needed replace. Thing is that any time you get a "check engine", the cruise will be disabled. you must clear the code, by either a trouble code diagnostic tool, or disconnect the battery for about five minutes. Codes will clear, and cruise will start working again.

Nov 19, 2010 | 2004 Isuzu Axiom

2 Answers

Where is the map sensor located on a 2004 rodeo


check the right side of the intake manifold or the right rear of the intake manifold...

Feb 03, 2010 | 2004 Isuzu Rodeo

1 Answer

Were is my ABS sensor located on my 2000 Isuzu Rodeo


there should be a sensor at all 4 wheels so make sure there all pluged in 

Jul 03, 2009 | 2000 Isuzu Rodeo

1 Answer

1997 isuzu rodeo


The firing order for a six cylinder is 1-2-3-4-5-6 distributor rotation-clockwise...cylinders 1-3-5 on drivers side...2-4-6 on passenger side

Dec 18, 2008 | 1997 Isuzu Rodeo

1 Answer

1999 Isuzu Rodeo LS, 4 wheel drive


it is probably a brake adjustment problem

Oct 18, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo S 3.5L V6 Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...