Question about 2004 Chevrolet Impala
Periodically my car makes a weird sound when it starts...when I started it tonight I noticed the clock had the wrong time...it had to be reset...What is the problem with the car??
Easiest and cheapest solution is to check the alternator if that is fine, I would have the timing belt checked next
Posted on Jan 01, 2013
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2004 Chevy Impala Brake Problem
I did a complet brake job on my 2004 Chevrolet Impala about two weeks ago, and i still have warning light on. Thw system is working great. So how do I turn off the warning Lights, Traction off light, Brake light, and in warning center Low brake fuild?
Posted on Sep 04, 2009
SOURCE: pass lock problems
Your Passlock may need to relearn the ignition keys, if the
ignition lock has gone bad like my in-laws Grand Am Gt, here is what i
did so they will not get stranded any more. Buy a Passlock by pass
module for around $70.00. You can order one from GMPASSLOCK.COM in the
mean time try resetting the Passlock. Good luck
Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.
Without a scan tool you may have momentary starter interruptions while history clears itself.
Posted on Jan 18, 2010
After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive
Posted on Mar 02, 2010
ur vehicle is in limp mode[ a safe mode ] which will get u home trying not to cause any damage to engine --theirs a few reasons the vehicle will do this-low oil pressure-transmission problem-have vehicle scanned most auto stores such as auto zone / advanced auto [check ur local area]do this service for free the code gives u a start point towards resolving ur problem
Posted on May 11, 2010
Tips for a great answer:
ENGINE HESITATES WHILE ACCELERATION
LOSS OF ACCELERATION
can be fuel pressure issue or it's the problem with accelerator pedal or its
clogged filters causing there.
are many other possibilities. I suggest you to go through the list of help
links mentioned below, these will help you to confirm where the actual fault
These details will help.
Nov 28, 2012 | 1999 Mercury Cougar
Nov 29, 2009 | 2004 Chevrolet Impala
Nov 15, 2009 | 2003 Chevrolet Impala
Nov 20, 2008 | 2003 Chevrolet TrailBlazer
Jul 08, 2008 | 2004 Chevrolet Impala
Dec 06, 2016 | 2004 Chevrolet Impala
64 people viewed this question
Usually answered in minutes!